Jump to content
Ultimaker Community of 3D Printing Experts

carmamir

Member
  • Content Count

    47
  • Joined

  • Last visited

Community Reputation

0 Neutral
  1. I can send you the files that I have generated. I have no idea where the original board from Ultimaker is coming from (I have boards from both shops). My spare board was bricked the same way that original Ultimaker. I have of course generated firmware for UMO (generated second file for second board checking it extra carefully).
  2. Only sensor to 104GT, and baud rate to 115200. Nothing else. First unresponsive board was to 104GT and sensor for heated bed + 225000 baud rate (I thought that baud rate caused that I cannot upload firmware either through Cura or Arduino IDE). I mean Arduino Mega 2560 (pretty much regular arduino board). After disconnecting original Arduino Mega board I wasn't able to upload anything (timeout) Cura / Arduino IDE. Same happened with second board (original Arduino Mega 2560). I have uploaded other firmware (Cura/Arduino IDE) before this one and had no issues. After I've uploaded a firmwar
  3. Does any one using https://bultimaker.bulles.eu/ ??? I have found it on Google. First firmware was done few days ago. After I've uploaded this firmware for Ultimaker basically I cannot connect with Ultimaker any more (however Arduino can read SN, but cannot upload anything, same with Cura (timeout)). I have decided to install another Arduino motherboard... As previously I have used 225000 as baud rate, I have select 115200 this time... Guess what... ANOTHER MOTHERBOARD DESTROYED !!! Timeout every time, doesn't mattery Cura/Arduino, laptop, Surface Pro, desktop, Windows 10, 7... I can rea
  4. Unfortunately I haven't checked it and it turned out that not my workstation or Surface Pro 3 supports baud rate 250000. Now I can't upload any other firmware (cura/arduino). What should I do ?
  5. ~1250 with filaments. Free delivery to Glasgow/Edinburgh included in price.
  6. I have UM for sell. My UM has: - heated bed (firmware recognize and working without any issue, temps up to 110 with aluminium bottom bed + glass top bed) - E3D hotend (I still have old UM hotend) - Enclosed case (nice 4mm thick doors (you can open each side) - LCD with SD reader (original) PM me for more information. I'm based in Scotland but I can deliver it across UK (costs depends from location). Everyone know cost of UM without heated bed, enclosure and E3D. Selling as currently I'm working a lot and simple I have no time to print anything. I have also ABS/PLA
  7. I have huge problem with E3D hotend, it's keep jamming, always I couldn't print anything bigger as ALWAYS it will jam. No matter what I'm printing, no matter what speed, it will jam. It's happening after 2-3hours of printing. Any idea ? Very annoying.
  8. Thanks it is popular e3d hot end from thingiverse, modified just a little bit. I have E3D hot end designed from scratch but it is for my 3D printer (I will try to release both printers and parts in March/May, I'm aiming into complex semi-professional quality 3D printer, lots of new exciting features (software/hardware as I'm after uni and I know something about electronics, developing software etc. :>)). I tested it against ABS version of this hot end. If you will use easy E3D hotend for Ultimaker from Thingivers and you will use heating cartridge from Ultimaker it might be difficult to p
  9. Send some box spec. How does look noise on your box ? Is 5V+ separated from any possible noise in your device ? Difficult to say if that would affect UM electronic (which is simply just Arduino + rebuild motor shield), the best way is to check what is current needed by your box, then check noise on oscilloscope of your 5+ and GND. I haven't checked schematics for motor shield on UM but I guess there will be one 5V+ line, so no matter where you will connect, just make sure that current will be appropriate for +5V line, and make sure that you won't connect some noisy device as it can affe
  10. Why don't you just use normal milling service ? Unless you like that burnt texture on wood. We have laser and mechanical cutting equipment and personally I prefer mechanical cutting over laser cutting.
  11. Finally I put E3D into my Ultimaker. I printed hotend mount in PLA and it melted down after few prints. So I decided to give a try to prepare some more rigid and reliable mount Wooden hotend mount , I even add some special "burnt texture" so it would match UM case . I've cut this mount on CNC (on 3 axis as I were too laze to centre material on 4th axis) What do you think about it ? My main concern about ABS mount is that it has 105 degrees melting point. Heated bed I used can get up to 115-120 without an issue :/ (plus I have enclosed UM case) I were testing E3D and look
  12. I uploaded firmware with EPCOS 100k and 4.7k pullup. Unfortunately temp still is wrong (first I tried without pullup) and shows 155. I used marlinbuilder, and option extruder temp sensor 100k thermistor - best choice for EPCOS 100k (4.7k pullup). Looks like Ultimaker still using default settings for AD595 instead of selected 100k (after I connect AD595 it will show correct temperature). Don't ask my why I don't want AD595. ***** Update Solved by removing IC component. Directly connected to Arduino it worked
×
×
  • Create New...