Jump to content

Ulti-Evening 4 April | Extrusion upgrade

SandervG

By SandervG
in Nederlands

 Share

Recommended Posts

SandervG

SandervG 1,521

Posted
Posted · Ulti-Evening 4 April | Extrusion upgrade

Hopelijk zien we elkaar ook weer op deze aankomende Ulti-Evening. Hij zal plaats vinden 4 April in Fablab Protospace. Het onderwerp van deze editie zal zijn; de Extrusion upgrade.

Mijn collega's Dennis en Marrit zullen uitleggen wat de verschillende verbeteringen zijn die in de Extrusion upgrade verwerkt zitten, en hoe deze te installeren.

Als je zelf er al een thuis hebt liggen, neem deze dan vooral mee en dan kun je hem tijdens de Ulti-Evening installeren, en eventueel kunnen we zelfs nog even meehelpen ook.

In het geval dat je de promo gemist hebt;

Tot dan!

Datum: 04 - 04 - 2016

Locatie: ProtoSpace Utrecht

17.00 - 18.00 Aankomst (Neem je Ultimaker mee!) en bestel eten (10 euro pp)

18.30 - 19.00 Presentatie

19.00 - 22.00 Extrusion upgrade installatie

    • Link to post
    Share on other sites
    • 2 weeks later...
    ultibrain

    ultibrain 5

    Posted
    Posted · Ulti-Evening 4 April | Extrusion upgrade

    Hi there,

    Ik rijdt vanavond vanuit Schiedam naar de meet. Ik vertrek zo tegen half zes. Als iemand mee wil rijden, dat kan, ik kan ophalen en afzetten bij station Schiedam.

    Voor degene die komt. Is er iemand die voor mij een set reserve lagertjes mee zou willen nemen? Mijn printer 'tikt'. Ik wil proberen of dat te verhelpen is door een nieuwe set lagers te monteren. Het gaat om de ball bearings (niet de koperen...).

    Groet!

    Merijn

    • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
     Share
    Go to topic listing

    • Our picks

      • UltiMaker Cura 5.7 stable released

        UltiMaker Cura 5.7 stable released

        ArunC posted a topic in UltiMaker Cura,

        Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
         
        • 18 replies
        MariMakes

        Picked By

        MariMakes,

      • Release Notes: S-Line Firmware 8.3.0 (Latest)

        Dustin posted a topic in Firmware,

        S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
        • 0 replies
        MariMakes

        Picked By

        MariMakes,
      View All
    ×
    ×
    • Create New...