Jump to content

Constant Material Jams


AlexW

Recommended Posts

Posted · Constant Material Jams

My company just bought an ultimaker 3.

I've had experience in the last 5 years with 4 or so other FDM machines from makerbot, lulzbot, and stratasys.

I want to like the ultimaker. It's by far the quietest machine I've used, has a great form factor for the size, and is pretty.

However I can't get it to print. The only successful print I have had is printing a test cube with 1mm (yes 1mm) layer height.

Everything else fails part way into the print. The nozzle must jam, and the extruder wheel cuts a nice chunk out of the filament and it's done. Have to re load the material which usually takes it a couple of tries to get right.

The last testcube I tried on "draft print" settings got about 20mm of the way up before it failed. Looked good right up until it didn't stopped.

I've tried:

The Silver PLA that came with the machine.

Lulzbot Gold PLA

Increasing and decreasing the tension on the extruder

Calibrating Z height.

What should I try next?

  • Link to post
    Share on other sites

    Posted · Constant Material Jams

    I should update my profile - I have been using the um3 for a month now.

    What layer height, speed and temperature are you printing at?

    When you have too much pressure in the head the force that the feeder exerts gets too high and it starts to grind at the feeder. The problem is possibly at the feeder but 95% chance the problem is at the head.

    If you print at 1mm layer height (yikes!) you need to keep the speed probably under about 8mm/sec with the .4mm nozzle. Or did you drill out the nozzle larger?

    Also check for filament tangles. I have more ideas but lets start with this.

  • Link to post
    Share on other sites

    Posted · Constant Material Jams

    Hi, thank you for your post.

    Lets keep that thought in mind, we all (want to) like Ultimaker!

    I think it is pretty unlikely that your nozzle jams, the print cores are very reliable.

    Can you upload some photo's from your feeder? What is the tension you have it set now?

    Do you have some photo's of your failed prints?

    - Why do you want to print at 1mm layer hight?

    At lower resolutions you can print faster and more reliable.

    With a 0.4mm nozzle, 1mm layer height is probably pushing the limits of what the nozzle can process.

    I would recommend to try another print, at something like 200 or 300 microns with the filament that came with the Ultimaker 3.

    Curious to hear how that goes!

  • Link to post
    Share on other sites

    Posted · Constant Material Jams

    Haha, the 1mm layer height was purely to see if the jamming was occurring due to the nozzle being pushed into the material. Not desired other than just out of interest.

    So, I went back to the material that came with the printer, the mid range tension on the extruder, and re applied the default settings in cura.

    I was able to print a draft quality and normal quality testcube. Both turned out great. I was impressed with the "normal" quality. It's not a normal quality in my opinion at all. Compared to other prints, I'd call it superfine quality haha. :)

    I'm running a 6.5hr print right now, and about an hour in. Assuming it is done when I get back into work tomorrow I'll call this good.

    After failing a print again with the gold material, I pulled the filament back to swap back to the silver material, I noticed that right at the head there was one of those "chew" marks in it.

    Before I got my hands on the printer, someone else here was playing with it. I suspect what happened may have been that an initial jam was caused by something, possibly the Z height being a little off, possibly a tangled spool, who knows. I did notice that the thin sample spool that came with the UM3 was thin enough to slide around on the holder and the filament could get off the side and tangle.

    After the initial jam, we might have pulled the filament out at the nozzle, trimmed up the end a little, then put it back in. Or perhaps failed attempts to correctly load fresh filament added a new chew point. Anyway, the chewed out section of filament was at this point somewhere between the extruder and the nozzle.

    Printer prints fine for a while. Then, once the chew section gets to the inlet to the heater cartridge, it jams up due to the weird shape.

    This happens a few times in a row while I start fiddling with other settings, trying to get things to work. Tension, layer height, different filaments, etc

    I guess I'll just have to be careful, and after a new filament load, inspect the filament as it travels through the bowden to ensure it looks free from marks.

    Anyhow, that's my figuring for now. Looks good anyway, still got to try PVA support and high quality. :)

    Thanks for suggestions. I'll keep you posted if I run into more problems!

  • Link to post
    Share on other sites

    Posted · Constant Material Jams

    I did notice that the thin sample spool that came with the UM3 was thin enough to slide around on the holder and the filament could get off the side and tangle.

    Thanks for suggestions. I'll keep you posted if I run into more problems!

    Could you share a photo of what the back of your Ultimaker 3 looks like, especially having both reels of filament, and how they are mounted, on the photo?

    Thanks!

  • Link to post
    Share on other sites

    Posted · Constant Material Jams

    Could you share a photo of what the back of your Ultimaker 3 looks like, especially having both reels of filament, and how they are mounted, on the photo?

     

    Sure,

    Here it is as I have it now:

    20161102_074244.thumb.jpg.9f167559bc36b0dab7b143c81580bf6d.jpg

    Here is what I noticed early on, while it was on a co-workers desk. I've kind of simulated what happened. It may have started with a backfeed, and the roll was almost full then, so that could have made it easier for it to come off the side:

    20161102_074300.thumb.jpg.d3d91e24d1e7177262b4f64e30c06eeb.jpg

    It could well have been because my co-worker's desk had a bunch of cables behind it also, so it could well have hit something to push it off centre. I haven't noticed this issue since it has been on my desk.

    -Alex.

    20161102_074244.thumb.jpg.9f167559bc36b0dab7b143c81580bf6d.jpg

    20161102_074300.thumb.jpg.d3d91e24d1e7177262b4f64e30c06eeb.jpg

  • Link to post
    Share on other sites

    Posted (edited) · Constant Material Jams

    I had similar issue trying out a 1.75mm filament, I was watching the filament very carefully as it was printing. 1/4 of the way through the print, it started to clog but just before that I noticed the filament had a couple of deep grind . I guess once those grinds go into the print core it just jams. My tension setting is right in the middle too.

    I will try again with some new UM3 filament coming soon.

    Here's a good link about under extrusion: https://ultimaker.com/en/resources/21477-how-to-fix-under-extrusion

    I've experience jam/under extrusion on the supplied UM3 filaments also. It's a tough nut to crack.

    Edited by Guest
  • Link to post
    Share on other sites

    Posted · Constant Material Jams

    Hi @AlexW, how is your Ultimaker 3 doing now? A grind probably also has some sharp edges and curling shreds of filament, and they can catch an edge somewhere in the printcore or on its way to it.

    I would not recommend to just insert 1.75mm filament, to do that reliably your printer would need more modifications.

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • UltiMaker Cura 5.8 Stable released 🎉
        In the Cura 5.8 stable release, everyone can now tune their Z seams to look better than ever. Method series users get access to new material profiles, and the base Method model now has a printer profile, meaning the whole Method series is now supported in Cura!
        • 5 replies
      • Introducing the UltiMaker Factor 4
        We are happy to announce the next evolution in the UltiMaker 3D printer lineup: the UltiMaker Factor 4 industrial-grade 3D printer, designed to take manufacturing to new levels of efficiency and reliability. Factor 4 is an end-to-end 3D printing solution for light industrial applications
          • Thanks
          • Like
        • 3 replies
    ×
    ×
    • Create New...