Jump to content

UMO+ Printing issues


loosemclaren

Recommended Posts

Posted · UMO+ Printing issues

Hi

Ive had my UMO+ for a year now. To be honest I'm very disappointed with it. I am sporadicly able to do nice prints for short periods of time. For instance in total frustration I replaced the entire feed line and hot end last weekend. Fantastic printing again no problems ace quality. one week on I'm back to my old problems of blocked nozzle continually cleaning it out and back to a 5-10% success rate. It will print for 20s fine then slowly slow down the amount of material from the nozzle. if you stop you are unable to retract the PLA as it is jammed in the feed somewhere near the PEEK block.

So F***k*d off with it.

Ive thrown all my PLA out and bought new pend a roll today and same old problems.

Ive rebuilt the feeder and done a lift test 4kg seems ok

Ive tried to manually feed the PLA into the hot end and you can just feel it get stiffer and stiffer until is stops.GRRRRRRR

Is there any other way than changing the hot end to a different design.

I can print ABS no problems...........

But I want to print PLA

Or other materials

Any ideas?

  • Link to post
    Share on other sites

    Posted · UMO+ Printing issues

    UMO+

    Print hours since the last time you changed the PTFE coupler? (It has a print life span of 50-200h depends on the temp) So it might be just that.

    Also photos, always photos. Show photos of your hotend setup, I seen many users that don't install it right and while it can work, it gives a lot of trouble.

    So.. I think you just need a new PTFE coupler. Also, some 3dsolex distributors sell a TFM coupler, that is a material that can resist the heat much longer and is the same material used on um2+ hotends, and on um2 can print for 500-2000h... I never seen anyone using it on umo+ (at least not on the forum) but should work much better than the standard.

  • Link to post
    Share on other sites

    Posted · UMO+ Printing issues

    Hi thanks for reply

    I changed the PTFE coupler last weekend and have done 5 prints since but 50 hrs is hardly anything. I often do prints that long.

    Im running innofil abs at 225 and trying to use some colourfab pla at 200.

    do you have any idea what happens to the page to cause issues? is it gripping on the filament or something? I will investigate some TFM parts

  • Link to post
    Share on other sites

    Posted · UMO+ Printing issues

    Hiya,

    I have experienced similar.

    I have resorted to having a set of nozzles for ABS and a set for PLA.

    I found that temp has a major part to play. for PLA i try and keep it as low as possible.

    reason i have different sets is that when I change between the two materials the change function goes to the temp of the last material ie: ABS 250 deg. This is where my problem lays as that temp with PLA causes it to powder up and block the nozzle. so I manually change it.

    using Simplify3D I retract using the control panel till its all the way out. drop the temp then change the nozzle to the PLA and then insert the PLA material.

    hope this helps

    kind regards

    becky

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Introducing the UltiMaker Factor 4
        We are happy to announce the next evolution in the UltiMaker 3D printer lineup: the UltiMaker Factor 4 industrial-grade 3D printer, designed to take manufacturing to new levels of efficiency and reliability. Factor 4 is an end-to-end 3D printing solution for light industrial applications
          • Thanks
          • Like
        • 3 replies
      • UltiMaker Cura 5.7 stable released
        Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
         
          • Like
        • 26 replies
    ×
    ×
    • Create New...