Jump to content

Vertical walls are very slanted


prinknash

Recommended Posts

Posted · Vertical walls are very slanted

I'm brand new to Ultimaker. On all my prints, vertical surfaces slant significantly (11 degrees) towards the negative x direction as they build up. In the y direction, they are nice and vertical. Any clues on what's wrong?

 

  • Link to post
    Share on other sites

    Posted · Vertical walls are very slanted

    Most likely you have loose pulleys on the X-axis mechanism. Be sure and tighten the motor and belt pulleys.

    While you are doing that, check that the head moves relatively easily by hand when the machine is powered off, in both X and Y directions. If it feels tighter in one direction, or stickier in some parts of the bed, then make sure that everything is square, and lubricate the rods with a little light oil (e.g., sewing machine oil). You might also try loosening the end caps on the rods a little, and see if that makes the head easier to move - sometime the end caps can bind on the ends of the rods.

     

  • Link to post
    Share on other sites

    Posted · Vertical walls are very slanted

    Thanks for the ideas. I've checked them out.

    The pulleys are very tight. I can't find slip anywhere in them. The head moves easily, and with the same amount of force in both the x and y directions and over the whole bed. The amount of slant is constant and seems to keep going (tallest part I've made is 2 inches so at 11 degrees, that's a 0.4 inch offset at the top. It seems there must be some slip somewhere to keep accumulating but it's only in one direction and on one axis and very consistent, meaning straight sides are very straight but slanted.

    Obviously I'm stumped.

     

  • Link to post
    Share on other sites

    Posted · Vertical walls are very slanted

    The only "true" way to check if the pulleys are properly secured is by putting a mark on them and on the axes, and see if they do not move independently. The pulleys can feel secured but could be a tiny bit lose, as you only have a tiny bit of slanting.

     

  • Link to post
    Share on other sites

    Posted · Vertical walls are very slanted

    I had the exact same problem on my X motor. I head scratched about it for hours until I noticed the X motor belt was twisting due to lightly touching the rear wood panel. I added washers to the existing black plastic spacers for the motor mount (and also mounted the x motor pulley as close to the motor as I could without it touching - maybe .5 mm?) and the slanting problem went away!

    By the way the slanting is caused by missed steps in the X motor servo.

     

  • Link to post
    Share on other sites

    Posted · Vertical walls are very slanted

    This is my first time in the forum. The advice is great. The "missing servo steps" explains why the angle gets steeper for parts longer in the x-direction. I don't see any belts rubbing but I can certainly track down the problem now. Thanks all.

     

  • Link to post
    Share on other sites

    Posted · Vertical walls are very slanted

    It's subtle. Print something simple and watch the belt the goes around the x-motor. If it's touching the back panel it will twist a different direction every time it switches direction.

     

  • Link to post
    Share on other sites

    Posted · Vertical walls are very slanted

    Thanks to all. I got it solved because of this forum. It was a friction issue in the x-drive, like gr5's problem but with a different reason. My x rod drive pulley was mounted 1/2 mm to far down the shaft. Since the pulley rides on the race of the rod bearing, this allowed more of the rod to protrude from the bearing and rub on the end plate. Moving the pulley slightly took care of it.

    Thinking the slant over, it's surprising how infrequent I was missing steps. An 11 degree angle is 0.2 radians meaning I was missing a single additional step in the +x direction every 5 layers to make the pattern skew to the negative x.

     

  • Link to post
    Share on other sites

    Posted · Vertical walls are very slanted

    I'm sure it was missing a partial step on every layer to be that consistent. I think these servos are driven in 1/8 step increments maybe? Does that make sense?

    You could have also fixed it by lowering "jerk" and acceleration to ridiculously low values.

     

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • UltiMaker Cura 5.8 Stable released 🎉
        In the Cura 5.8 stable release, everyone can now tune their Z seams to look better than ever. Method series users get access to new material profiles, and the base Method model now has a printer profile, meaning the whole Method series is now supported in Cura!
        • 5 replies
      • Introducing the UltiMaker Factor 4
        We are happy to announce the next evolution in the UltiMaker 3D printer lineup: the UltiMaker Factor 4 industrial-grade 3D printer, designed to take manufacturing to new levels of efficiency and reliability. Factor 4 is an end-to-end 3D printing solution for light industrial applications
          • Thanks
          • Like
        • 3 replies
    ×
    ×
    • Create New...