Jump to content

Cura erster Layer

theAndreas

By theAndreas
in Deutsch

 Share

Recommended Posts

theAndreas

theAndreas 0

Posted
Posted · Cura erster Layer

Hallo Forum,

 

ab der Cura Version 3.3 sliced wird der erste Layer von innen nach außen gedruckt. Vorher wurde von außen nach innen gedruckt. Das lieferte bei mir wesentlich bessere Ergebnisse.

 

Cura Version 3.2.1

image.thumb.png.d2ab4801dc8f3baee721bf5192853a7c.png

 

Cura Version ab 3.3

image.png.6117897933a8c410b8570b163e569f9c.png

 

Habe bereits alle Einstellungen durchsucht aber nichts dazu gefunden. Weiß irgendjemand warum sich das geändert hat bzw. wo man das umstellen kann?

 

Vielen Dank für die Hilfe!

 

Gruß Andreas

    • Link to post
    Share on other sites
    • 4 weeks later...
    theAndreas

    theAndreas 0

    Posted
    • Author
    Posted · Cura erster Layer

    Hallo,

     

     

    On 10/29/2018 at 7:59 PM, Nicolinux said:

    Hi, habe dazu auch nichts gefunde. Stell die Frage vielleicht auch im englischen Teil des Forums in der Software-Kategorie.

     

    werd ich mal probieren.

     

    Gruß Andreas

    • Link to post
    Share on other sites
    • 2 months later...
    zerspaner_gerd

    zerspaner_gerd 382

    Posted
    Posted · Cura erster Layer

    Nein,

     

     

    Aber ehrlich gesagt ist in den englischen Post nicht mal die rede von der druck Reihenfolge des ersten Layers (innen nach außen, außen nach innen)

    Sondern nur von Unterschiede der Versionen und eine Einstellung für die erste Schicht aber welche 🤔

    • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
     Share
    Followers 1
    Go to topic listing

    • Our picks

      • UltiMaker Cura 5.7 stable released

        UltiMaker Cura 5.7 stable released

        ArunC posted a topic in UltiMaker Cura,

        Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
         
          • Like
        • 18 replies
        MariMakes

        Picked By

        MariMakes,

      • Release Notes: S-Line Firmware 8.3.0 (Latest)

        Dustin posted a topic in Firmware,

        S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
          • Like
        • 0 replies
        MariMakes

        Picked By

        MariMakes,
      View All
    ×
    ×
    • Create New...