Jump to content

UM3 Auto Leveling Not Working


Ronan

Recommended Posts

Posted · UM3 Auto Leveling Not Working

Hi all, been awhile (been extremely busy with my 3D printing business 🙂 ).

 

So one of our army of UM3 is giving us issues (its always the same one... the first one we bought the moment the UM3's came out). Warranty is long gone too...

 

This time the auto leveling isn't working. I spent 3 hours on it with no success.

 

What i tried/did:

Clean both print heads.

Change print heads.

Tighten the bed fully to give it 14mm space before doing a dozen manual leveling and automatic leveling (automatic leveling = head touches glass every time when it starts).

Check the red sensor wire, looks fine, its fully seated.

 

What can i do? Right now it's doing a test print in after manually leveling the bed and turning auto bed level off.

 

Since we run at 100% capacity (we have 2 SLS, 2 SLA, 4 UM3 and 6 Prusa MK3) We can't really afford having any printers down...

 

Any help would be greatly appreciated before we have to send it in out of warranty (can't imagine the cost of that... brrrr).

 

Also any tips/tricks in printing on a UM3 in manual leveling mode? Same as Um2?

 

Thank you!

  • Link to post
    Share on other sites

    Posted · UM3 Auto Leveling Not Working

    When I first inquired about this when I got my first UM3E (right after product launch), I remember being told here that the machine is susceptible to RF interference.

     

    With that machine, I have had to do what you did. Manually level and just print.

     

    It does not happen all the time, but when it does, I have to do as you did and then a bit later, it goes back to normal.

    • Like 1
    Link to post
    Share on other sites

    Posted · UM3 Auto Leveling Not Working
    1 hour ago, kmanstudios said:

    When I first inquired about this when I got my first UM3E (right after product launch), I remember being told here that the machine is susceptible to RF interference.

     

    With that machine, I have had to do what you did. Manually level and just print.

     

    It does not happen all the time, but when it does, I have to do as you did and then a bit later, it goes back to normal.

    VERY interesting. Something to keep an eye on.

  • Link to post
    Share on other sites

    Posted · UM3 Auto Leveling Not Working

    I am hoping someone from Team Ultimaker will see this to verify or, clarify this. My memory ain't so good since surgery.

     

    It may be just general electrical interference.

     

    The good thing is that you can turn off the active leveling after manual leveling. It generally lasts as long as you have the same buildplate in place.

  • Link to post
    Share on other sites

    Posted · UM3 Auto Leveling Not Working

    We change buildplates nearly daily. We have a dozen spare glass buildplates, precoated, so we can quick swap.

     

    Hence why we spent a fortune on the UM3's, quite a few of them, because of reliability. Might grab one or two S5's but unsure. UM3's are nice, but i have not been impressed with the aftersale customer service. It seems those machines are hit/miss, might get a really good one or a really shitty one. Although in all fairness... i think that was a first/second batch issue, which is understandable.

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Introducing the UltiMaker Factor 4
        We are happy to announce the next evolution in the UltiMaker 3D printer lineup: the UltiMaker Factor 4 industrial-grade 3D printer, designed to take manufacturing to new levels of efficiency and reliability. Factor 4 is an end-to-end 3D printing solution for light industrial applications
          • Thanks
          • Like
        • 3 replies
      • UltiMaker Cura 5.7 stable released
        Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
         
          • Like
        • 26 replies
    ×
    ×
    • Create New...