UltiMaker uses functional, analytical and tracking cookies. Tracking cookies enhance your experience on our website and may also collect your personal data outside of Ultimaker websites. If you agree with the use of tracking cookies, click “I agree, continue browsing”. You can withdraw your consent at any time. If you do not consent with the use of tracking cookies, click “Refuse”. You can find more information about cookies on our Privacy and Cookie Policy page.
The recommendation is in principle ok, because different materials have different pressure temperatures and there can always be a rest in the nozzle.
But if you clean the PrintCore regularly or after every change from one type of material to another, i.e. with hot/cold pulls, then I don't see any problem.
I don't use dedicated PrintCores and also don't do a Hot/Cold Pull very often and don't have any problems with it. But that doesn't mean that this is the correct way. I think this is rather a question of faith how to handle it. With dedicated PrintCores for every kind of material you certainly don't do anything wrong, if it's really necessary, I can't say, but I personally haven't noticed any disadvantages after one year.
When a nozzle is worn out, you can see from the print quality, as the nozzle no longer has the intended diameter and has become wider. So far (1 year) I haven't seen any wear on my PrintCores.
First of all PLA and TPLA are 99.99% the same thing as far as I'm concerned. It's like water versus water with food coloring. They have very similar temperature characteristics, same melting point, same softening point, they act the same in almost every way except the TPLA is slightly more flexible and slightly weaker. This makes it quite a bit tougher. So definitely one core for both of those is fine.
So I swap between nylon and pla with the same core all the time. I already swapped twice today. It's really not a big deal. When I switch to PLA however I don't tell the printer that it's not nylon right away - just slide out the nylon, slide in the pla, then do "move material" and wait until all the nylon seems to be gone. Only then do I select "pla" as the "current" material. I do this because I feel you need the higher temp to get most of the nylon out of the nozzle.
I don't print much TPU so I can't really speak to that but changing cores all the time seems a bit silly. I have used the same core for maybe 8 different materials including PP, ABS, PLA, TPU, Nylon, CPE
As far as I can tell the cores last forever. I've had a few cores that I've used for I think about 2 years now? They are build very well and will probably never wear out - they just might snap at the heatbreak some day - other than that I expect them to last years.
Thanks for the information. Ae will stick witht he print cores we have at present and keep them cleam. A couple of spare print cores in the drawer just in case.
Link to post
Share on other sites
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
In the Cura 5.8 stable release, everyone can now tune their Z seams to look better than ever. Method series users get access to new material profiles, and the base Method model now has a printer profile, meaning the whole Method series is now supported in Cura!
We are happy to announce the next evolution in the UltiMaker 3D printer lineup: the UltiMaker Factor 4 industrial-grade 3D printer, designed to take manufacturing to new levels of efficiency and reliability. Factor 4 is an end-to-end 3D printing solution for light industrial applications
Recommended Posts
Smithy 1,145
The recommendation is in principle ok, because different materials have different pressure temperatures and there can always be a rest in the nozzle.
But if you clean the PrintCore regularly or after every change from one type of material to another, i.e. with hot/cold pulls, then I don't see any problem.
I don't use dedicated PrintCores and also don't do a Hot/Cold Pull very often and don't have any problems with it. But that doesn't mean that this is the correct way. I think this is rather a question of faith how to handle it. With dedicated PrintCores for every kind of material you certainly don't do anything wrong, if it's really necessary, I can't say, but I personally haven't noticed any disadvantages after one year.
When a nozzle is worn out, you can see from the print quality, as the nozzle no longer has the intended diameter and has become wider. So far (1 year) I haven't seen any wear on my PrintCores.
Link to post
Share on other sites
gr5 2,224
First of all PLA and TPLA are 99.99% the same thing as far as I'm concerned. It's like water versus water with food coloring. They have very similar temperature characteristics, same melting point, same softening point, they act the same in almost every way except the TPLA is slightly more flexible and slightly weaker. This makes it quite a bit tougher. So definitely one core for both of those is fine.
So I swap between nylon and pla with the same core all the time. I already swapped twice today. It's really not a big deal. When I switch to PLA however I don't tell the printer that it's not nylon right away - just slide out the nylon, slide in the pla, then do "move material" and wait until all the nylon seems to be gone. Only then do I select "pla" as the "current" material. I do this because I feel you need the higher temp to get most of the nylon out of the nozzle.
I don't print much TPU so I can't really speak to that but changing cores all the time seems a bit silly. I have used the same core for maybe 8 different materials including PP, ABS, PLA, TPU, Nylon, CPE
As far as I can tell the cores last forever. I've had a few cores that I've used for I think about 2 years now? They are build very well and will probably never wear out - they just might snap at the heatbreak some day - other than that I expect them to last years.
Link to post
Share on other sites
John_Mag 0
Thanks for the information. Ae will stick witht he print cores we have at present and keep them cleam. A couple of spare print cores in the drawer just in case.
Link to post
Share on other sites