Jump to content

cura4.3.0 not spiralizing outer contour

scott208

By scott208
in UltiMaker Cura

 Share

Recommended Posts

scott208

scott208 0

Posted
Posted · cura4.3.0 not spiralizing outer contour

so i just installed cura 4.3.0 with all of the standard settings for the cr-10 and when i enable spiralized outer contour i still get a z seam and not a continous z movement

here is some g code it made


G92 E0
G92 E0
;LAYER_COUNT:762
;LAYER:0
M107
G0 F6000 X88.337 Y88.412 Z0.2
;TYPE:SKIRT
G1 F1200 X88.582 Y88.168 E0.0115
G1 X89.389 Y87.39 E0.04878
G1 X89.533 Y87.254 E0.05537
G1 X91.96 Y84.997 E0.1656
G1 X92.094 Y84.875 E0.17163
G1 X92.453 Y84.552 E0.18769
G1 X92.707 Y84.33 E0.19891
G1 X93.575 Y83.596 E0.23672
G1 X93.734 Y83.464 E0.2436
G1 X96.353 Y81.332 E0.35592
G1 X96.481 Y81.229 E0.36138
G1 X96.88 Y80.914 E0.37829
G1 X97.154 Y80.705 E0.38975
G1 X98.053 Y80.04 E0.42694
G1 X98.219 Y79.92 E0.43376
G1 X100.925 Y77.995 E0.54421
G1 X101.087 Y77.881 E0.5508
G1 X101.477 Y77.614 E0.56652

    • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
     Share
    Go to topic listing

    • Our picks

      • UltiMaker Cura 5.7 stable released

        UltiMaker Cura 5.7 stable released

        ArunC posted a topic in UltiMaker Cura,

        Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
         
          • Like
        • 18 replies
        MariMakes

        Picked By

        MariMakes,

      • Release Notes: S-Line Firmware 8.3.0 (Latest)

        Dustin posted a topic in Firmware,

        S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
          • Like
        • 0 replies
        MariMakes

        Picked By

        MariMakes,
      View All
    ×
    ×
    • Create New...