Jump to content

Ultimaker 2 retracts fialment about 200mm after printing is finished

Mcgyver

By Mcgyver
in UltiMaker 3D printers

 Share

Recommended Posts

Mcgyver

Mcgyver 0

Posted
Posted · Ultimaker 2 retracts fialment about 200mm after printing is finished

Hey

As mentioned: Our UM2 retracts filament about 200mm after printing is done.

About 2 month ago i updated the software on the machine, still worked after that.

I hade issues with Cura 4.6 that the nozzle stopped in the print when finished so i read here a little and upgraded to 4.8 and that issue went away, but now i have another issue.

 

The printer is running firmware 3.3.0

 

Any help would be appreciated.

 

Here's the start and end of the G-code if that helps.

;FLAVOR:UltiGCode
;TIME:1424
;MATERIAL:1309
;MATERIAL2:0
;NOZZLE_DIAMETER:0.4
;MINX:89.779
;MINY:99.991
;MINZ:0.3
;MAXX:133.222
;MAXY:122.474
;MAXZ:5.58
;Generated with Cura_SteamEngine 4.8.0
M82 ;absolute extrusion mode
G0 F3000 Y50 ;avoid prime blob
G92 E0
G92 E0
G10
;LAYER_COUNT:45
;LAYER:0
M107
G0 F3600 X93.488 Y102.953 Z0.3
;TYPE:SKIRT

 

-------------------------------------------------------------

 

;TIME_ELAPSED:1424.057764
G10
M107
M25 ;Stop reading from this point on.
M82 ;absolute extrusion mode
;End of Gcode

    • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
     Share
    Go to topic listing

    • Our picks

      • UltiMaker Cura 5.7 stable released

        UltiMaker Cura 5.7 stable released

        ArunC posted a topic in UltiMaker Cura,

        Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
         
          • Like
        • 23 replies
        MariMakes

        Picked By

        MariMakes,

      • Release Notes: S-Line Firmware 8.3.0 (Latest)

        Dustin posted a topic in Firmware,

        S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
          • Like
        • 0 replies
        MariMakes

        Picked By

        MariMakes,
      View All
    ×
    ×
    • Create New...