bob-hepple
-
Posts
624 -
Joined
-
Last visited
-
Days Won
3
Content Type
Forums
Events
3D Prints
Posts posted by bob-hepple
-
-
Tinkergnome - thanks for the reply yes you are correct I am making the cables myself as long as I keep everything wired the same it should be fine then? Yes I am aware they are wired in series originally I said parallel my mistake? Working on presumption yellow is pos,, Ordering the connectors today I suppose the connectors don’t have to be exact. Thanks for you input 8m intsalling you firmware later today/tomorrow.
Bob.
-
ok did some searching Rs came up with
https://uk.rs-online.com/web/p/products/8201529/
cripms
820-1611 Fan Plug
515-1383 Fan Socket
-
why 10 ?? thought it was 1 um2
-
Ok I'm on the march wiring the Mark 2 have 2 questions...
q1 my second Bondtech - where on the mother board does it plug inn (stupid question but I have to ask...
q2 Im using Syntax Terrors board, when it comes to the model fans I was going to copy the original UM Wiring,, ie I think they are parralel,, any reason not too.. voltage ect.
Just need to find the connectors Male and female, any RS numbers would be helpfull if anyone has them.
-
Go Bondtech and you wont look back
-
1
-
-
can you send the link to what you have seen,
-
I purchased a cheap tumbler Rubber pots and a small motor.. and yes I'm in the UK you could get the rubbers and make your own motor driver
-
I know you can stop the Priming pillar when your finished doing dual head prints but forgot how to do it can anyone help PLEASE>>>>
-
Ultiiarjan
Thanks for the reply I managed to get the cable header on very snug fit all six pins connected.. Just being over cautious
-
Hi I have begun wiring the Mark 2, Mod using Syntax Terrors Extension Kit there is a 6 way ribbon connector that meets a six pin header, it is extremely tight fit and I wondered does only three of these pins marry up with the Locking Ribbon Cable Header,
to get all 6 marry up is very tight and it looks like the pin spacing is larger on the header...
hence I thought I would ask before I screw it up..
Thanks in advance
-
I Like that, Yeah I had a few issues printing the head, and I was fighting with another printer, so didn't want to have 2 on the go, I ripped the bed off the UM2 so I have no choice now but to do the Wring (this weekend if all goes to plan) if not next week,, LOL but thanks for Asking
-
I looked at the Rais and for the bed levelling I would not go there,, I like the look of the UM3 but if you have a pruisa what about LULZbot Taz 6
-
as this person want's a point and click solution to 3d printing (which I think is unrealistic) I think it is a real mistake to mix Gcode flavours, that's just increasing the pain.
-
jpyt - glad I made sense, the mark 2 is the second head Mod for the UM2 I don't know whether the 2+ is also an intended machine to retro fit to.
the link
https://magnetic-tool-changer.com/#top
the air duct is some thing I came up with, for the second head which I have started to install, on going project it will probably be installed by Christmas and then probably sell the machine. Glad you like it.
-
on the UM2 the spring was done away with and used a spacer< by in screwing the stainless steel part you put pressure on the i2K
I use 3d Solex Parts All the Time
hope this helps.....
-
1
-
-
ReFI30)r
that's a hell of a name - I see no body has answered you, I cant help I'm afraid as I haven't finished my install, I hope support for this mod is not waining, hopefully some will answer you???
-
well said every one point made !! Me thinks.
-
Thanks for the advise I will re print Low extrusion rate ??
-
glued the mags in place and put it all together but there is no gap
https://magnetic-tool-changer.com/assets/images/build/16.jpg
should this be ok or re print
-
got my head put together and mags glued in but there is no gap as per the instructions do we think it will make a difference??
-
Totally understood, when I place the two parts together there is no gap.
-
foehnsturm
thanks for reply I had it as well in space claim,
-
Stu
yep I have read that about the glue but I think mine is not right, there is no gap
https://magnetic-tool-changer.com/assets/images/build/16.jpg
will investigate before I strip machine..
-
On a thread I have posted, I thought I would modify the coupling, So I imported the Step file to Soldiworks and find the dimensions are all wrong by I think x10 hole in the coupling wings is 3mm in my Sw it is 33.60 I did some searching but couldn't find much about Sw and step that answered the question..
any help appreciated.
UM2+ Extended FAN Upgrade
in Third party products & modifications
Posted
MTG
sorry no one answered (it happens) I would personally check the fans for voltage the fact the model fans are wired in series will make the difference.