Jump to content

ultimaker 3 connect to secure wifi network


limburgmetaal

Recommended Posts

Posted (edited) · ultimaker 3 connect to secure wifi network

can anybody tell me how to add the ultimaker 3 to an excisting wifi network?

the wifi setup gives a hotpoint, but i can't find that on my win7 network connectors

we did ask the vendor of the machine,but got no reply

Edited by Guest
  • Link to post
    Share on other sites

    Posted · ultimaker 3 connect to secure wifi network

    dear neotko

    i might been not clear, no this link is not the solution at all.

    with my windows 7 i don't get a pop-up and even if i ask to look for a new network, it will not give a connection.

    the question is, how to link the printer to the excisting network

  • Link to post
    Share on other sites

    Posted · ultimaker 3 connect to secure wifi network

    Hi, plug in your Ultimaker 3 to your router via an Ethernet cable. On the printer got to settings/network run down the selection and to "LAN cable". At the bottom of the screen you should see the internet address (eg 192.168.107) note this. Now go to a computer on your network and fire up a web browser and type the printer address you noted, in the address bar, which should bring up "Welcome to your Ultimaker 3"  page with a start a "Start WIFI setup" button on it.

  • Link to post
    Share on other sites

    Posted · ultimaker 3 connect to secure wifi network

    Can you try with your phone?

     

    thanks, but the idear on the network is to send files and to use the camera at the off-hourse printing,

    The mobile option does not add any fjnction as i see it now.

  • Link to post
    Share on other sites

    Posted · ultimaker 3 connect to secure wifi network

     

    Can you try with your phone?

     

    thanks, but the idear on the network is to send files and to use the camera at the off-hourse printing,

    The mobile option does not add any fjnction as i see it now.

     

    I just mean to finish the wifi setup

  • Link to post
    Share on other sites

    Posted · ultimaker 3 connect to secure wifi network

     

    Can you try with your phone?

     

    thanks, but the idear on the network is to send files and to use the camera at the off-hourse printing,

    The mobile option does not add any fjnction as i see it now.

     

    And unless you set up a VPN network (@UltiArjan did it) the monitoring only works when you are logged in on the same network as your Ultimaker 3 is connected to.
  • Link to post
    Share on other sites

    Posted · ultimaker 3 connect to secure wifi network

    And unless you set up a VPN network (@UltiArjan did it) the monitoring only works when you are logged in on the same network as your Ultimaker 3 is connected to.

     

    yeah, I was surprised how easy it is, depends on the type of router you have ofc. but with a "fritzbox" router it's a matter of a few minutes.

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
          • Like
        • 0 replies
      • Ultimaker Cura 5.6 stable released
        Cura now supports Method series printers!
         
        A year after the merger of Ultimaker and MakerBotQQ, we have unlocked the ability for users of our Method series printers to slice files using UltiMaker Cura. As of this release, users can find profiles for our Method and Method XL printers, as well as material profiles for ABS-R, ABS-CF, and RapidRinse. Meaning it’s now possible to use either Cura or the existing cloud-slicing software CloudPrint when printing with these printers or materials
        • 48 replies
    ×
    ×
    • Create New...