Jump to content

Seem to not get notifications anymore


kmanstudios

Recommended Posts

Posted · Seem to not get notifications anymore

For some reason, I do not get notifications anymore for any replies or messages. I got them for the longest time. I checked just now to see if any settings got reset in my notifications, they did not.

I only see the little thingies in the top right when I log in.

Spam filter is not the problem (double check that daily) and it is not blacklisted in the mail and does not wind up in the trash either.

  • Link to post
    Share on other sites

    Posted (edited) · Seem to not get notifications anymore

    Hi @kmanstudios, thank you for your message. hmm, that doesn't sound right.

    The day of the server migration we had email issues for one day, but that was resolved. Let me see if I can detect any oddities in the emails that were sent.

    Can you elaborate on your experience a little bit more? Do you not get any notifications at all? During one day, since a couple of days?

    Thanks!

    Edited by Guest
  • Link to post
    Share on other sites

    Posted · Seem to not get notifications anymore

    Well, I got a few today after I posted that. But when I got here there were 7 notifications in my lil' bell symbol at top right, but only 3 emails.

    It has been like this for a while. Maybe a week or two. And, it is possible I am here often enough that I beat the notification system. Wonder what the lag is between a posting to follow and the time sent out......

  • Link to post
    Share on other sites

    Posted · Seem to not get notifications anymore

    I got them since yesterday (dunno if it was all, but at least some). @Neotko, you got none? @kmanstudios, did you get more emails today?

    We fixed the bug yesterday, and there were quite a few emails pending from notifications which were not sent. The server could decide not to send out all pending emails at once, to prevent them from being blacklisted by sending email in bulk (could raise some flags). Perhaps it will be a few days before everything is up to date again, and any delay is gone.

    If you have any details, so many notifications - so many emails, let me know so I can give more specific feedback to our dev's. Thanks!

  • Link to post
    Share on other sites

    Posted (edited) · Seem to not get notifications anymore

    I got them since yesterday (dunno if it was all, but at least some). @Neotko, you got none? @kmanstudios, did you get more emails today?

    We fixed the bug yesterday, and there were quite a few emails pending from notifications which were not sent. The server could decide not to send out all pending emails at once, to prevent them from being blacklisted by sending email in bulk (could raise some flags). Perhaps it will be a few days before everything is up to date again, and any delay is gone.

    If you have any details, so many notifications - so many emails, let me know so I can give more specific feedback to our dev's. Thanks!

    Curious. I got an email for this tag.

    Edited by Guest
  • Link to post
    Share on other sites

    Posted · Seem to not get notifications anymore

    I did get the notifications this morning. I get that bit of not flooding the email servers as it can cause the issues of being blacklisted automatically. I did however whitelist the Ultimaker emails on my end because a few wound up in the spam filter a while back.

    But, I seem to be back up and running now.

    Thanks!!

    • Like 1
    Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • UltiMaker Cura 5.7 stable released
        Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
         
          • Like
        • 18 replies
      • S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
          • Like
        • 0 replies
    ×
    ×
    • Create New...