Jump to content

The two most annoying problems with my S5 Bundle


Jonas98

Recommended Posts

Posted (edited) · The two most annoying problems with my S5 Bundle

 

My personal day ruiner... 10 trys, no start.

3 Months everthying was great.

Now again that .....

How can Ultimker think its an good idea to put an that susceptile sensor into an "industrial" machine

The "test" says Sensor is good....

 

I have to print something and cant use the printer.....Thats extremly annoying

 

IMG_20200624_074114.thumb.jpg.606fccc778aa9ccbb7e088f66555f46d.jpg

 

In the "best" case just a dirty printer, in the worst case an blocking Z axis.

 

IMG_20200624_074140.thumb.jpg.3e0b771bbc216a1297a648e417799404.jpg

IMG_20200122_201652.thumb.jpg.98259dd23f6cae3a49e055c47e6cb955.jpg

 

Please fix this....

An reliable printing would be much more usefull than any cloud funktionality

 

 

Edited by Jonas98
  • Link to post
    Share on other sites

    Posted · The two most annoying problems with my S5 Bundle

    Hi Jonas, thank you for your message. In the latest firmware update the priming sequence has been updated so it should prime less material. Obviously what it still primes does end up on the bottom of your machine but this is necessary to ensure a successful next print when you switch materials and when the Material Station automatically loads material.

    My German is a little bit rusty, but unless I'm wrong the display informs you that it couldn't complete the active leveling. Has this been resolved in the mean time? Let us know if you need any further help. Thanks, 

  • Link to post
    Share on other sites

    Posted · The two most annoying problems with my S5 Bundle
    5 hours ago, SandervG said:

    Hi Jonas, thank you for your message. In the latest firmware update the priming sequence has been updated so it should prime less material. Obviously what it still primes does end up on the bottom of your machine but this is necessary to ensure a successful next print when you switch materials and when the Material Station automatically loads material.

    My German is a little bit rusty, but unless I'm wrong the display informs you that it couldn't complete the active leveling. Has this been resolved in the mean time? Let us know if you need any further help. Thanks, 

     

     

    Hi,

    I priming sequence is a lttle bit better.

    But if you have to cancle the print and wait for it it is still very long.


    yes cant complete the auto leveling

     

    I fixed this by soldering the cables at the capazitive board and replaced the crimp conctacts at the cables.

    Till now it is working.....I hope for a long time.

     

    I think the leveling is too susceptible

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
          • Like
        • 0 replies
      • Ultimaker Cura 5.6 stable released
        Cura now supports Method series printers!
         
        A year after the merger of Ultimaker and MakerBotQQ, we have unlocked the ability for users of our Method series printers to slice files using UltiMaker Cura. As of this release, users can find profiles for our Method and Method XL printers, as well as material profiles for ABS-R, ABS-CF, and RapidRinse. Meaning it’s now possible to use either Cura or the existing cloud-slicing software CloudPrint when printing with these printers or materials
        • 48 replies
    ×
    ×
    • Create New...