Jump to content

YvesRossignol

Member
 View Profile  See their activity

  • Posts

    32

  • Joined

  • Last visited

 Content Type 

Everything posted by YvesRossignol

  1. YvesRossignol
    I need to replace the bed levelling spring (I lost one...) don't ask me how! where i can buy a new one?
  2. YvesRossignol
    thanks for all, i will try it.
  3. YvesRossignol
    my bed temperature is 60, and nozzle printcore temperature is 220. Line width 0.69, line height 0.13... I use simplify to have more printing speed.
  4. YvesRossignol
    Hi, As you can see, I need more material to have a good first layer. I add more material with extrusion multplier up to 1.1 but it doesnt work. The filament seam to be stuck... I clean the nozzle between each print. I use solex printcore with 0.6 nozzle (ice). I just made a print very good with the same parameter.... Yves
  5. YvesRossignol
    To be sure.... George help me a lot. Thanks you kmanstudios, these two guys want to help. Nobody else want to help except for money here in canada.
  6. YvesRossignol
    Hi, I come back with my experience into this problem. first of all, Printcore are not into warranty. Second, printcore is one part. Cannot have nozzle and ptfe tube. third, ptfe molt a lower temperature that you believe... Unfortunatly, the only one answer I had... you will have to pay... ok, it's the hard way to understand. So... thank to George Robert from his store... (gr5.com) and thanks for all, Yves
  7. YvesRossignol
    @gr5 Can you tell me how I can have more strenght force from the extruder??? The filament seem to slip for me. Thanks for all your help.
  8. YvesRossignol
    Thanks again, I will try to have a replacement part from reseller but the silicon is "glue" in place. I think I will have to change nozzle and silicon tube. Any web site you know for that.... Yves
  9. YvesRossignol
    Dear kmanstudios, your advices are very very important. Thanks, I have made a lot of mistake without you. Yves
  10. YvesRossignol
    I think I have find my problem, the silicon tube is melten into 2 of my printcores (I have 3 printcore AA). Can you tell me where I can have a replacement part? I will probably change the hotend and try to recover the electronic pieces
  11. YvesRossignol
    I have print more than 120 days.... since my beginning and I have an accident with nylon (910) the printcore lower end was stuck but nylon... and my printer head was damaged by this accident a little bit (the bracket is never completly closed since the repair by less than 0.5 millimeter. My problem begin with the printer unable to do auto-level because of a sensor problem (there is a problem with sensor message) - i do manual leveling many time and now it seem ok Yves
  12. YvesRossignol
    for the breakaway is it the AA printcore... maybe my mistake....
  13. YvesRossignol
    Thank for information a) yes same parameter b) I'M able to pull the filament too easily maybe less than 4 kg.... c) I think the silicon insert is burn... where can I find new one... it's ok for the garantee.... I think the feeder's gear are dirty but I can't see, can I have more force for the filament... (b) maybe the filament is more weak (surface more less hard) Do you have replacement printcore (last option) where I can have good printcore (in fact very good print core)
  14. YvesRossignol
    I understand the bad tolerance and i see it in action on this spool. The breakable filament is from ultimaker. I dont find it in other brand. I will find and make more test and reply to this topic with my experience... if i find... thank you sir.
  15. YvesRossignol
    filament.ca econofill pla (16$ CDN / kg !) extrusion multiplier into simplify, and débit (flow rate) in Cura (I see a problem, it is just for first layer in cura...) nozzle clean, each time material stuck in print core it's "breakable" the fist picture: gcode made by cura at 120% of flow rate... (default print speed is 60mm/s or 3600mm/min) the two others: made by simplify 3d... at 100% extrusion multiplier and 120%... with filament diameter to 2.72mm (print speed 80 mm/s) Thanks for all Yves
  16. YvesRossignol
    Hi, I have many printing problem with my Ultimaker 3extended since few weeks. Sometime the external skin doesnt print, the infill is inconsistent. I use simplify3d and cura and try many settings. my filament is grey PLA with 2.72 mm diameter (economical filament, but I use a lot of filament, 8 to 12 kg per month), i try from 100% to 120% print speed and temprature from 220 to 240 for extruder. Print bed is 70 C. The filament seem to slip sometime. And the printcore 2 is unavailable because it is stuck with material. I'm unabe to clean after many hours of hot and cold pull. Do you have any idea? I think my printcores are scrap! Thank for all your advice. the last picture is my biggest print (in five parts) and I need to work on precision.... It's not glue perfectly... Yves
  17. YvesRossignol
    Hi, I have the following error "difference between printcores...." so I think it was time to make a bed leveling...but in manual mode... I tried to turn the screws to have one mm but the bed is too low... the screws were at the end of what they are able to unscrew....I still have 2 mm and nothing to turn on screw.... any ideas? (all 3 screws) Yves
  18. YvesRossignol
    It's work now My experience: - always use silicon pad because airflow are very bad without it and the temperature rise and you will have an er15 code. - always use the good adhesive for bed... - talk with the communauty and ultimaker. Bye
  19. YvesRossignol
    Now, my printhead work and I have an error er15 in slot 1. It take about 15 minutes and the printer stop because of heater too hot in printcore1. I lost (unable to recover) the small silicon shield at the tip of the printcore1. But I have max temperature at 285C for print core 1 and 385C !!! for printcore2 in the maintenance menu.
  20. YvesRossignol
    I think i will change the printhead and the printcores... 700$ USD ??? and where I can have it quickly. (I find printhead from frbc8 but is it good part ?) Can i have one from ultimaker ? 408+2*114 = 636$ usd plus transport, duty fee, taxes, usd to cdn dollar = 1000$....
  21. YvesRossignol
    I was able to connect the printhead and heat up to 300C I removed all nylon that i can but the printcore can't go up and down while I'm using the two "plate" in front of printcore (one is black the lower one) and the other is white. Since I have an error with printer (er12) I can't heat the printcore and reset the printer
  22. YvesRossignol
    look comment on this picture. Can I remove chemicaly Nylon ?
  23. YvesRossignol
    Do you think my print head will be destroy? look at this picture, I still have Nylon... How to remove printcore tip (nozzle) and square plate? I can't have access to the upper bolt.... I don't have so small tool...
  24. YvesRossignol
    The switch for printcore is disassemble now. But nylon is still there. I will take picture.
  25. YvesRossignol
    I will try heat gun because i have nylon stuck between aluminium part and copper (yellow) of the printcore and it can't move freely.
×
×
  • Create New...