Jump to content

Heat Bed causing UM2 to turn off


JoshMaurici

Recommended Posts

Posted (edited) · Heat Bed causing UM2 to turn off

Hey All,

So when the build plate for my Ultimaker 2 starts to heat up i think there's a short somewhere, causing  the printer  to restart its self. Feels like its earthing out somewhere.

I've checked all the wires connected to the bed and all the solders are fine.

Only other information i can give is I've tested the bed when disconnected from the printer and got a reading of 30 ohms. Not sure if that's what its supposed to be giving off or not.

Any thoughts on this? should i just order a new heat bed? Is there anything else i could do to troubleshoot the problem?

Thanks In advance,

Josh

UPDATE: There is this small burn mark on the heat bed itself. This could be causing the problem?

UM2.thumb.JPG.2b412d9c0fd0c0262ae4aa527ef9ac8a.JPG

UM2.thumb.JPG.2b412d9c0fd0c0262ae4aa527ef9ac8a.JPG

Edited by Guest
  • Link to post
    Share on other sites

    Posted · Heat Bed causing UM2 to turn off

    A few quick options:

    - Check if you are not using an Ultimaker 2 Go power supply unit.

    - Check if on the electronics end or the bed-end none of the wires are touching.

    - Feel free to upload a picture of your electronics terminal on which the heaters are connected to check for burned marks or anything strange.

    - 4th option; your heated bed is broken.

  • Link to post
    Share on other sites

    Posted (edited) · Heat Bed causing UM2 to turn off

    So i managed to get a new heat bed but it did not fix the problem. Ive noticed that there is some slight discoloration on back of the pcb of the motherboard. Is this normal? It seems like its a tad burned.  IMG_2212.thumb.JPG.6d418d2e6eaf2a9653afd0522b56eeab.JPG

    Also here is a video of what happens on the motherboard when i try to heat up the bed.

     

    IMG_2212.thumb.JPG.6d418d2e6eaf2a9653afd0522b56eeab.JPG

    Edited by Guest
  • Link to post
    Share on other sites

    Posted (edited) · Heat Bed causing UM2 to turn off

    Have you tried only heating the bed (and nothing else?) It could be that all the systems combined draw to much power, causing the UM2 to turn off.

     

    yes. Ive tried manually heating the bed and as soon as it begins to heat up it shorts out and turns off then back on. Ive also tried isolating the two wires that connect from the motherboard to the heat bed. this was to check if the UM2's wires are faulty but even when i used new wires it didnt fix the problem.

    Edited by Guest
  • Link to post
    Share on other sites

    Posted (edited) · Heat Bed causing UM2 to turn off

    A few quick options:

    - Check if you are not using an Ultimaker 2 Go power supply unit.

    - Check if on the electronics end or the bed-end none of the wires are touching.

    - Feel free to upload a picture of your electronics terminal on which the heaters are connected to check for burned marks or anything strange.

    - 4th option; your heated bed is broken.

     

    checked all these. Power supply is the correct one.

    None of the wires are touching.

    Heat bed is not broken as i replaced it with a brand new one and still didnt fix the problem.

    I have uploaded a pic of the back of the motherboard (post above) were it looks a tad burned.

    Edited by Guest
  • Link to post
    Share on other sites

    Posted · Heat Bed causing UM2 to turn off

    I have no idea why everyone is looking at the heated bed - it seems much more likely the power brick is defective.

    I'm an electrical engineer so I would measure the current coming out of the brick for the 1 second that the heated bed is on but that's tricky to do. I would just ask your supplier to send you another power brick. They are a bit expensive.

    30 ohms is too high - that would be only about 25 Watts for the bed, but it's more like 100 watts so it should be about 6 ohms (not 30 ohms). I think you somehow measured it wrong.

    The brown stain on the board is far from the heated bed connection so I think unrelated.

    • Like 1
    Link to post
    Share on other sites

    Posted · Heat Bed causing UM2 to turn off

    I have no idea why everyone is looking at the heated bed - it seems much more likely the power brick is defective.

    I'm an electrical engineer so I would measure the current coming out of the brick for the 1 second that the heated bed is on but that's tricky to do.   I would just ask your supplier to send you another power brick.  They are a bit expensive.

    30 ohms is too high - that would be only about 25 Watts for the bed, but it's more like 100 watts so it should be about 6 ohms (not 30 ohms).  I think you somehow measured it wrong.

    The brown stain on the board is far from the heated bed connection so I think unrelated.

     

    so turns out it was the power brick that was shorting out. Got a replacement one and it works fine.

    Thanks for your help.

    • Like 1
    Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • UltiMaker Cura 5.8 Stable released 🎉
        In the Cura 5.8 stable release, everyone can now tune their Z seams to look better than ever. Method series users get access to new material profiles, and the base Method model now has a printer profile, meaning the whole Method series is now supported in Cura!
        • 5 replies
      • Introducing the UltiMaker Factor 4
        We are happy to announce the next evolution in the UltiMaker 3D printer lineup: the UltiMaker Factor 4 industrial-grade 3D printer, designed to take manufacturing to new levels of efficiency and reliability. Factor 4 is an end-to-end 3D printing solution for light industrial applications
          • Thanks
          • Like
        • 3 replies
    ×
    ×
    • Create New...