Ultimaker filament feeder bowden tube replacement to direct drive.

[rod 3]

Hi all.

       Just uploaded my latest Ultimaker mod to youtube k9JoSJg7SIQ

                                                                                                                     Rod

Edited December 31, 2016 by Guest

[ultiarjan 1,223]

very cool !!!

is the print quality good? can you share some more details and close ups of the feeder?

 

[rod 3]

Hi print quality is very good. more consistant than with the bowden tube feeder.

Rod[/media][/media][/media][/media][/media]

[rod 3]

[rod 3]

[rod 3]

[rod 3]

[rod 3]

[rod 3]

[DidierKlein 729]

That's a pretty cool a idea to make a lightweight direct drive, i'm guessing that the extra weight is not that much and has no impact on vibrations when printing faster.

Are you planning to make it available somewhere ? The gears are metal or printed? Are you using the same motor as the original feeder?

Awesome work anyway!

[rod 3]

That's a pretty cool a idea to make a lightweight direct drive, i'm guessing that the extra weight is not that much and has no impact on vibrations when printing faster.

Are you planning to make it available somewhere ? The gears are metal or printed? Are you using the same motor as the original feeder?

Awesome work anyway!

 

Hi

Feedhead weight now 49grms .I removed the material cooling fans scrouding ect a year ago and replaced with air from a pump witch fans out just below the hot end nozzle .The only fan i use is to cool my hotend setup whitch is not standard

so should be a lot lighter than the original. Bevel gears are brass motor is the

original ultimaker material feed motor.As to making feeder a kit all depends on the

cost and feedback i get back.Now working on idears fo MK 2.

Thanks all for your interest.

Rod.

[BrayChristopher 36]

 

The bowden fan is an interesting idea.

https://ultimaker.com/en/community/3435-new-fan-cooling-design#reply-19327

https://ultimaker.com/en/community/3435-new-fan-cooling-design#reply-19299

[rod 3]

Hi just finished latest mod to enable me [/media]to remove printhead feeder assembly

allowing me to change ptfe or to convert to use 1.7 filliment.By removing the

single screw in the centre of the printhead an lifting up takes about 10 sec.

Rod

[LePaul 323]

Looks like you picked the right username for this drive feature

[rod 3]

Looks like you picked the right username for this drive feature  

 

Hi Thanks.

[rod 3]

 

 

The bowden fan is an interesting idea.

https://ultimaker.com/en/community/3435-new-fan-cooling-design#reply-19327

https://ultimaker.com/en/community/3435-new-fan-cooling-design#reply-19299

 

Hi replacing the fans with an airjet has worked out well for me as it gives

me more control of temp when printing.Fans can produce to mutch air to the wrong place that can have an adverse efect on buildplate temp and nozzle temp

resulting in bad prints and other problems plus they add extra weight to the moving printhead. I printed a Tourbillon watch by Christoph Laimer with the airjet with very few problems.

Rod[/media]

[rod 3]

Hi

Just finished latest mod to Bowden tube feeder replacement to enable me to feed and print 1.75 Ninjaflex flexable filliment. Test prints turned out as good as PLA or

better.

Rod[/media][/media]

[rod 3]

[rod 3]

[rod 3]

Hi

A few more mods plus tidy up and weight reduction off moving parts.

1/ Manual feed wheel added to step motor.

2/Steel cross material feed shaft replaced with carbon fibre shaft.

3/Carbon fibre shaft and bearing added to support any pull on head by filliment that might effect print quality.

Rod

[rod 3]

[rod 3]