Jump to content

well it was going to happen


0235

Recommended Posts

Posted · well it was going to happen

https://www.ultimaker.com/products/ultimaker-original

damn, that's not only a knife in the chest of the price drop, but then its being twisted with not only the doodle3d but a FREE Uti-controller :/

on the bright side though, could this mean a drop in the price of the ulticontroller? and nothing is better than having more people enjoy the joys of assembling there own 3D printer, and making sure its an ultimaker :)

but damn, that price drop is the whole PS4 i had to cancel :/

 

  • Link to post
    Share on other sites

    Posted · well it was going to happen

    I saw that too, I just hope it is not a sign of the UM1 to disappear :/

    and a cheaper UltiController would pull me over the edge to finally buy one.

     

  • Link to post
    Share on other sites

    Posted · well it was going to happen

    true !! but for a lot of people that dont have so much money... a super ultimaker for that price is really really... TASTY :-)

    If I wasnt working and living in officially the worst paid state in all of germany (Leipzig Saxony), I would grab one of these...

    But im more busys super glueing pennys together for my next electricity bill...... welcome to the DDR... oh excuse me... East Germany ! ;)

    Ian ;)

     

  • Link to post
    Share on other sites

    Posted · well it was going to happen

    oh but Ian.... you have so many good beers over there :p

     

  • Link to post
    Share on other sites

    Posted · well it was going to happen

    true !.... mmmmmm beer... thats a good idea !

    Havent got ratty drunk in ages... thanks for the tip !!

    Have a great weekend with your new ultimaker2 !!

    Ian :-)

     

  • Link to post
    Share on other sites

    Posted · well it was going to happen

    I saw that too, I just hope it is not a sign of the UM1 to disappear :/

     

    Never. They can pry the kit out of my cold dead hands. (FYI, I work at Ultimaker)

     

  • Link to post
    Share on other sites

    Posted · well it was going to happen

    I second daids comment.

     

  • Link to post
    Share on other sites

    Posted · well it was going to happen

    same here... but with small alterations...

    Never. They can pry the kit out of my warm cuddly irish loving hands....

    Ian LOL ;-)

     

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • UltiMaker Cura 5.7 stable released
        Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
         
        • 18 replies
      • S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
        • 0 replies
    ×
    ×
    • Create New...