UltiMaker uses functional, analytical and tracking cookies. Tracking cookies enhance your experience on our website and may also collect your personal data outside of Ultimaker websites. If you agree with the use of tracking cookies, click “I agree, continue browsing”. You can withdraw your consent at any time. If you do not consent with the use of tracking cookies, click “Refuse”. You can find more information about cookies on our Privacy and Cookie Policy page.
Hello. My printer is an Ender 3 Pro so it is much like yours.
The "Anti backlash spring nuts" and "Dual Z axis kit" can wait. (I've never had a need for either.) If the Z kit is a belt drive or is going to run off a splitter then you can install it whenever you want. There are some that require a second Z port on the mainboard. You may need to look at that depending on the kit.
The "Bowden Tube" is a consumable. The piece that goes into the hot end gets damaged both at the nozzle, and from the jaws of the fitting that holds it. Usually just nipping 6 or 7mms off the end and then sticking it back in will give you another bunch of prints. Eventually it gets too short and then you will need the new one. You may as well wait on that install as well. When cutting the tube I would recommend a single edge razor. That cut must be as close to a perfect 90° as you can get it or you will have problems with clogging between the nozzle and the bowden.
The aluminum Extruder should be put on right away. The stock Creality extruder has a failure rate of near 100%.
I level with a piece of paper (but the software I've written has movement commands for leveling so I don't use the knob). If the CRTouch does NOT require a firmware update then you can install it whenever you want. If it does need a firmware update then you may want to wait until you get more familiar with the whole "update the firmware" thing. It can be a deep dark hole.
Getting that first layer to stick requires that the plastic gets squished to the bed. Calibrating the E-Steps is a big part of that. If not enough plastic is being pushed (under-extrusion) then you will struggle getting prints to stick.
Spherical shapes are tough. I am assuming that flaw you see is the Z seam where the outer wall extrusion starts and stops. It can be moved but you can't hide it on a round shape as there aren't any corners to hide it in.
Finally...The top of the egg requires support on the inside. Like Z seams - there are always "steps" in a print that are 1 layer height high. It's the nature of the process. When those steps are too far apart (geometry of the model) then they will fall in if they aren't supported.
Link to post
Share on other sites
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
In the Cura 5.8 stable release, everyone can now tune their Z seams to look better than ever. Method series users get access to new material profiles, and the base Method model now has a printer profile, meaning the whole Method series is now supported in Cura!
We are happy to announce the next evolution in the UltiMaker 3D printer lineup: the UltiMaker Factor 4 industrial-grade 3D printer, designed to take manufacturing to new levels of efficiency and reliability. Factor 4 is an end-to-end 3D printing solution for light industrial applications
Recommended Posts
GregValiant 1,342
Hello. My printer is an Ender 3 Pro so it is much like yours.
The "Anti backlash spring nuts" and "Dual Z axis kit" can wait. (I've never had a need for either.) If the Z kit is a belt drive or is going to run off a splitter then you can install it whenever you want. There are some that require a second Z port on the mainboard. You may need to look at that depending on the kit.
The "Bowden Tube" is a consumable. The piece that goes into the hot end gets damaged both at the nozzle, and from the jaws of the fitting that holds it. Usually just nipping 6 or 7mms off the end and then sticking it back in will give you another bunch of prints. Eventually it gets too short and then you will need the new one. You may as well wait on that install as well. When cutting the tube I would recommend a single edge razor. That cut must be as close to a perfect 90° as you can get it or you will have problems with clogging between the nozzle and the bowden.
The aluminum Extruder should be put on right away. The stock Creality extruder has a failure rate of near 100%.
I level with a piece of paper (but the software I've written has movement commands for leveling so I don't use the knob). If the CRTouch does NOT require a firmware update then you can install it whenever you want. If it does need a firmware update then you may want to wait until you get more familiar with the whole "update the firmware" thing. It can be a deep dark hole.
Getting that first layer to stick requires that the plastic gets squished to the bed. Calibrating the E-Steps is a big part of that. If not enough plastic is being pushed (under-extrusion) then you will struggle getting prints to stick.
Spherical shapes are tough. I am assuming that flaw you see is the Z seam where the outer wall extrusion starts and stops. It can be moved but you can't hide it on a round shape as there aren't any corners to hide it in.
Finally...The top of the egg requires support on the inside. Like Z seams - there are always "steps" in a print that are 1 layer height high. It's the nature of the process. When those steps are too far apart (geometry of the model) then they will fall in if they aren't supported.
Link to post
Share on other sites