-
Posts
691 -
Joined
-
Last visited
-
Days Won
1
Content Type
Forums
Events
3D Prints
Posts posted by Blizz
-
-
Its actually midnight NL. NYC is -4, we're at +2 and it will be at 6pm.
-
Zoals ik zei: Ik denk dat ik persoonlijk veel geholpen zou zijn initieel met een glossary. Dan moet je niet elk begrip gaan liggen opzoeken. Bij voorkeur ook nog eens met fotos erbij
-
My first test with bronzefill:
It's about 7cm high.
Post processing wise I sanded it to get rid of some of the debris, but nothing else yet. I'm considering getting copper polish to try to get it a bit more shiny.
-
Leon het probleem is gewoon: Hoe onderhoud je zoiets, hoe ga je het structureren? Iedere mens denkt anders. Alles veranderd ook zo snel. Een soort van glossary ergens zou alleszins een zeer nuttig iets zijn, dat veranderd niet vaak. Maar een manual, dunno. Lijkt me zeer lastig om up to date te houden.
-
Arjan: Ja inderdaad was ik ook net achter Die 0.3 is wsl wel de oorzaak van de pillowing. Als er een 0.1mm laagdikte gebruikt is zijn dat maar 3 lagen, da's niet genoeg om het netjes dicht te krijgen (afhankelijk van de infill)
-
gr5 i was in London
But thanks for the Rome tip... hope it'll pass here well in advance, always like the opportunity to go to Rome.
-
Wish I could go too... But flying from Belgium to NYC just to see the makerfaire...can't afford that.
-
I think you should remove the quotes from "250000", so just use 250000.
The box probably tries to convert this into an integer but fails because of them.
-
Kijk trouwens ook even hier:
http://support.3dverkstan.se/article/23-a-visual-ultimaker-troubleshooting-guide#pillowing
-
Een UM2 kan kwalitatief ongeveer 10mm3/s aan. Alles hoger gaat achteruit.
De instellingen die jij daar aanhaalt komen neer op
0.4mm (nozzle) * 100mm/s (snelheid) * 1mm (laagdikte) = 40mm3/s
Er is geen UM2 die dat deftig kan printen volgens mij.
Gezien de instellingen verbaast het me enorm dat het resultaat nog zo goed is, chapeau van Ultimaker!
Ik druk meestal af tussen 0.1 a 0.25 mm laagdikte (afhankelijk van de kwaliteit die ik wil en met een snelheid van 30 tot 75mm/sec. Hangt er allemaal beetje vanaf hoeveel geduld ik heb
Bij hogere "vloeisnelheden" kan het nuttig zijn om de temperatuur te verhogen trouwens, aangezien het filament zo snel door de nozzle moet dat het niet eens de kans krijgt om deftig te smelten.
-
Apparently not:
I don't think there will be a live feed Ian..
-
Conz: imo the users can really figure it out themselves in 5 seconds flat if they really wanted to. It's not that it is unclear where the option is. After you create a topic you are redirected to it and the "follow this topic" really stands out.
-
I'm using both those things already (but thanks for the tips), but as Amedee said: You have to click all the icons for all forums. So a mark everything would still be a good thing imo.
-
Lol okay... Thanks guys for pointing that out, had no idea they would use my print in the commercial. Good thing they professionally hid the burnt top
-
Actually I don't, but since pm_dude was saying that nobody noticed, I just wanted to say: i did!
-
Will it be that UM-mini that Daid was working on 2 Ulti-eve's ago?
I mean...Just saying
-
I'd love a "mark everything read" function please. It's a lot of work having to reset each forum separately. If I end a visit, I like to come back with a clean slate
-
Het probleem met Ultimaker is volgens mij dat de tickets zeer slecht tot bij iemand geraken die het opvolgt (en blijft opvolgen). Basically: De service is brak tot er iemand zich met je ticket bezighoud en dan gaat het schitterend en wordt alles meer dan correct afgehandeld. Soms valt het ook weer stil (omdat er bvb een dag of wat over gaat tussen antwoorden) en dan moet je hier in het forum weer komen irri doen tot Sander (of iemand anders) een poke gaat uitdelen.
Ik denk dat het gewoon een kwestie is van slechte interne tools en veel te druk, niet van onwil. Dus wat mij betreft krijgen ze nog wat "credit". Moet wel zeggen dat ik het haat ik om zo te moeten bedelen voor aandacht als ik een ticket aanmaak, moet gewoon opgelost geraken.
-
Jup... All that commotion for a lid! That would be the disappointment of the year haha.
-
Will it be that UM-mini that Daid was working on 2 Ulti-eve's ago?
-
Definitely not dual extrusion. Daid just replied in the official topic about it that they re-assigned him from cura to research for dual extrusion. This means (assuming he's telling the truth - sorry Daid), that they're really not ready with that.
-
Quick print of an iPhone6 and iPhone6+ for a "pocket test".
Just wanted to know if the 6+ will be annoying to carry around due to its size.
For me, the answer is - unfortunately - an overwhelming yes.
Hardware-wise this is the only of the 2 phones that remotely comes close to the current top range android phones. I was considering purchasing one, but given my level of annoyance it'll have to be a "regular 6"
-
Geen probleem hier met die shroud. Deze raakt het warme gedeelte niet en zit gewoon vast, dus zelf al zou de zijkant wat plastisch worden, het beweegt allemaal niet dus geen prob.
Ik heb de indruk dat het wel helpt, maar ik heb het nog niet praktisch uitgetest, dus da's geen objectieve mening.
-
I bought 10m of bowden from ebay, to have some spare stuff. Haven't tried it yet on the printer as mine is fine, but the specs said that it was for the UM2. Perhaps that might be an idea for a possible future rage fit?
Nozzle temperature - remember setting ?
in UltiMaker Cura
Posted
The temperature for the nozzle stays at 0 in a print until the bed temperature has been stabilised. Are you sure it's not that?