Smokie

oke if forgotten to copy the m117 line now its working thanks diving duck!!

hello diving duck thanks fore the reply i have tried already some things my qu are : must i do this in the new cura version how to do this so i dont have to do it every time again maby a bit stupid but i cant get it working wr Henk

hello i would like to use the same start g code as in cura 3.10 in the newer version(s) 3.6 or 4.0 how to do this? wr Henk

found an old post that pointed me in the right direction https://community.ultimaker.com/topic/19494-circles-are-not-fully-round/ my x / y frame was not 90 degrees square have tacled this with braces and the print result is finally good w r Henk

Well, if changed the stepper but no(the same) result Dont know were to look now for a sollution? Wr Henk

have checked every bolt a more closer look shows a mistake in the print direction at 4 places see image now i think that the y axis stepper motor skips steps at direction change have ordered a new one fingers crossed?

Hello I have simmelair problems Wonderd if and how you solved the problem Wr Henl

Thanks for the reply John printer wanhao duplicator v2.1/ 0.4 nozzle/ PLA /Cura 3.1 0.2-brimm 0.8-wall 0.8-top/b0.8-comp wall overlaps-hide seam-infill 20--retr 1.5-cooling-speed 60 mm/s pos see picture im chekking belts/stepper report back if there are results wr Henk

Maby not the best picture Effekt occurs on two places see pic

Hello Im having problems with printing round forms would like some sugg Wr Henk see picture

All interesting options to try but my problem is how to upgrade to the new cura version(s) and resulting in a better print Wr Henk

I know PC does and is recommended. Hello Started with 16.0.1(black) has a raft/brim option Than 15.04.6 also After that 2.6.2 and 2.7 with al kind of options Normal a raft gives me the best result with sticking to the bed but with bad bottom result The skirt option in 2.7 works fore the bottom (in custom mode) Wr Henk

Now with skirt isto raft Bottom is better only a z seam is still vissable Wr Henk

That looks horrible.... Was that a default um profile? Yes in both versions Fore me its still a puzzle why every new version looks to give a worst result Wr Henk Do you have a link to the model? hope this link works:https://www.dropbox.com/home?preview=bus.stl wr Henk

That looks horrible.... Was that a default um profile? Yes in both versions Fore me its still a puzzle why every new version looks to give a worst result Wr Henk

struggling struggling:( to much possibillities isnt always resulting in a better print left 2.7 rigth 15.04 long way to go fore me! wr Henk

Hello Cant open GCode generated in version 2.6.2 with a simulation progam Wat am i doing wrong? Wr Henk

After 1 1/2 week of problems finally printing with a good result!! Was drawing the reeds in 123design all from start and saw the options 1)to show the part 2)part with constr lines 3)constr lines only Never paid notions to that but i tried the option 1(part only) After that saved the stl and conv to g code in cura The g gode in a simulation showed a good print and the real print was now also with a good result without allthe problems of the last week So i think the constr lines were the problem in conversion with cura Wr Henk

tried all that,but no result can't reed the G code but i think its what you say ,pussing too much fillament from layer 5 and further but there is no fillament comming out will experiment futher thanks fore the support wr Henk

In a viewer it looks okay Print starts okay layer 5 and following the extruder stops The movement cont After a few layers its clear that the extruder is not starting anymore Tried in more cura verions The fillament is grinded and clogged fore the pfte

In a viewer it looks okay Print starts okay layer 5 and following the extruder stops The movement cont After a few layers its clear that the extruder is not starting anymore Tried in more cura verions

https://www.dropbox.com/s/t6xazu3rh8msavc/reed%207.5%20new.stl?dl=0 hope this works wr Henk

how to upload an STL file?

thanks for the reply tried all versions of cura , best results with 16.0.1 came with the duplicator i3 firts results were okay after experimenting with cura the problem of stopping extruder after first layer occ see pictures wr Henk [/media]

hello, raft and first layer with infill are good the following layer there isnot comming anny fillament out of the extruder design drawn in 123d , converted to stl and g code in cura(tried all versions) were to look fore the mistake? all help is welkom! wr Henk