Jump to content

Printer kan niet tegen lange prints

datisniels

By datisniels
in Nederlands

 Share

Recommended Posts

datisniels

datisniels 0

Posted
Posted · Printer kan niet tegen lange prints

Hoi ik heb een probleem met mijn Ultimaker Original plus Elke keer wanneer ik een langere print aan zet van meer dan 2 uur Print hij niks meer en moet ik daarna de printkop weer ontstoppen weet iemand wat er mis mee is?

    • Link to post
    Share on other sites
    SandervG

    SandervG 1,518

    Posted
    Posted · Printer kan niet tegen lange prints

    Ha Niels, heb je ook een paar foto's van je Ultimaker, zodat we je printkop goed kunnen zien én je feeder van een paar verschillende hoeken?

    Wanneer je printer vastloopt en er geen filament meer uitkomt, kun je dan wel handmatig het filament er achter uit trekken, zonder weerstand? (als je printer nog aanstaat?)

    Zit er een blob op het puntje van je filament?

    Zit je bowden tube er goed in, als je deze vastpakt en omhoog trekt zou er vrijwel geen speling in moeten zitten.

    Heb je modificaties aan je Ultimaker gedaan?

    En print je PLA? Weet je welk merk?

    Alvast bedankt!

    • Link to post
    Share on other sites
    ahoeben

    ahoeben 1,800

    Posted
    Posted · Printer kan niet tegen lange prints

    Ik zeg: PTFE coupler. Na verloop van tijd vervormt het kanaal. Als er dan materiaal in de PTFE coupler stolt, dan zit het klem in dit onderdeel.

    • Link to post
    Share on other sites
    SandervG

    SandervG 1,518

    Posted
    Posted · Printer kan niet tegen lange prints

    Mogelijkheid kan ook nog zijn dat de feeder na een tijdje zijn spanning verliest, of er een blob in het filament komt onder de bowden tube, wanneer daar teveel speling in zit.

    • Link to post
    Share on other sites
    datisniels

    datisniels 0

    Posted
    • Author
    Posted · Printer kan niet tegen lange prints

    Ik ben de extruder maar uit elkaar gaan halen schoon gaan maken en daarna kijk ik wel of het gaat lukken

    • Link to post
    Share on other sites
    SandervG

    SandervG 1,518

    Posted
    Posted · Printer kan niet tegen lange prints

    Wat beschouw je als extruder, de printkop of de feeder?

    Er stonden boven nog wat vragen open welke wellicht een indicatie kunnen geven waar het probleem zich precies bevind.

    Succes, hopelijk is een goede schoonmaakbeurt alles wat er nodig is.

    • Link to post
    Share on other sites
    datisniels

    datisniels 0

    Posted
    • Author
    Posted · Printer kan niet tegen lange prints

    Ik heb hem schoongemaakt en hij werkt nu weer beter dus bedant voor alle tips etc.

    • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
     Share
    Followers 1
    Go to topic listing

    • Our picks

      • UltiMaker Cura 5.3 stable released

        UltiMaker Cura 5.3 stable released

        ArunC posted a topic in UltiMaker Cura,

        In this stable release, Cura 5.3 achieves yet another huge leap forward in 3D printing thanks to material interlocking! As well as introducing an expanded recommended print settings menu and lots of print quality improvements. Not to mention, a whole bunch of new printer profiles for non-UltiMaker printers!
          • Thanks
          • Like
        • 56 replies
        MariMakes

        Picked By

        MariMakes,
      • Here it is. The new UltiMaker S7

        Here it is. The new UltiMaker S7

        MariMakes posted a topic in Official news,

        The UltiMaker S7 is built on the success of the UltiMaker S5 and its design decisions were heavily based on feedback from customers.
         
         
        So what’s new?
        The obvious change is the S7’s height. It now includes an integrated Air Manager. This filters the exhaust air of every print and also improves build temperature stability. To further enclose the build chamber the S7 only has one magnetically latched door.
         
        The build stack has also been completely redesigned. A PEI-coated flexible steel build plate makes a big difference to productivity. Not only do you not need tools to pop a printed part off. But we also don’t recommend using or adhesion structures for UltiMaker materials (except PC, because...it’s PC). Along with that, 4 pins and 25 magnets make it easy to replace the flex plate perfectly – even with one hand.
         
        The re-engineered print head has an inductive sensor which reduces noise when probing the build plate. This effectively makes it much harder to not achieve a perfect first layer, improving overall print success. We also reversed the front fan direction (fewer plastic hairs, less maintenance), made the print core door magnets stronger, and add a sensor that helps avoid flooding.
         

         
        The UltiMaker S7 also includes quality of life improvements:
        Reliable bed tilt compensation (no more thumbscrews) 2.4 and 5 GHz Wi-Fi A 1080p camera (mounted higher for a better view) Compatibility with 280+ Marketplace materials Compatibility with S5 project files (no reslicing needed) And a whole lot more  
        Curious to see the S7 in action?
        We’re hosting a free tech demo on February 7.
        It will be live and you can ask any questions to our CTO, Miguel Calvo.
        Register here for the Webinar
          • Like
        • 18 replies
        MariMakes

        Picked By

        MariMakes,
      • UltiMaker Cura Alpha 🎄 Tree Support Spotlight 🎄

        Cura Alpha With New Tree Support 🎄

        MariMakes posted a topic in UltiMaker Cura,

        Are you a fan of tree support, but dislike the removal process and the amount of filament it uses? Then we would like to invite you to try this special release of UltiMaker Cura. Brought to you by our special community contributor @thomasrahm
         
        We generated a special version of Cura 5.2 called 5.3.0 Alpha + Xmas. The only changes we introduced compared to UltiMaker Cura 5.2.1 are those which are needed for the new supports. So keep in mind, this is not a sneak peek for Cura 5.3 (there are some really cool new features coming up) but a spotlight release highlighting this new version of tree supports.  
          • Like
        • 29 replies
        MariMakes

        Picked By

        MariMakes,
      View All
    ×
    ×
    • Create New...