3.2.1 crashes using 3.1 configuration files

[DrOldies 0]

Cura 3.2.1 crashes on installation whether I remove 3.1 or not. Selecting the 3.2.1 install notice to clear & restart gives a successful install but all config and profile files are erased. If I move my backup config files back to the their appdata folder, 3.2 crashed on startup. I removed 3.2 and did a clean install (new config files). Copying over just my profiles crashes 3.2. This may be because I did not copy the right group of files. Cura 3.2.0 also had these problems. The only non-standard setup in my Cura environment is that I have disabled "Materials" and use different Profiles for each material.  

 

 The error log with several install and start attempts is attached.

 

stderr.log

windows 10

current working version: Cura 3.1

updating to Cura 3.2.1

"Materials" configuration disabled

Machine other\Prussa i3 (ANET A8)

[ahoeben 1,955]

What do you mean when you say you disabled materials?

[DrOldies 0]

I changed a config flag so that the material field is not displayed. I enter changes between filaments in the profile and name the profile to identify the filament settings with the other settings changes. For example: "INLAND PLA Blue 0.2/60" I have never found an explanation of how the material configuration works with the profile configuration. Which takes precedence over the other in the applied settings? I doubt this is causing the error, but just wanted to point this out.

[ahoeben 1,955]

Can you zip up your 3.1 config folder and post a link here so we can have a look what goes wrong in 3.2?

[heinzel 0]

The same to me.

In result of the crash I lost every of my Cura settings. With a backup, I was able to somehow restore the version 3.1.

But I did not know where all my Settings are.

 

Please could anybody explain me, where on a Windows PC all the Settings are? I mean for my Printer itself, Material, the printersettings.

I was a little bit desperated.

 

With 3.2.1 i could not add Octoprint as a Printer - but why?

 

Edited February 25, 2018 by heinzel

[DrOldies 0]

To find the settings open cura. Under help select Show Configuration Folder. When you select this it will display the path and files.

[DrOldies 0]

Attached are

1. current 3.1 folder

2. the 3.2 zip file I found after selecting the clear option during install.

3. I added .log for uploading

 

 

cura 31 definitions.zip.log

3.2_20180223_143240.zip.log

[DrOldies 0]

For the lost settings, find the settings path as above:

To find the settings open cura. Under help select Show Configuration Folder. When you select this it will display the path and files.

Go there with explorer. I found a zip file created by cura 3.2 with my 3.1 settings. It was named 3.2_23536 or similar.

Unzip into the settings path. 

[heinzel 0]

Thank you. I will see, what I can do here to save as first many settings. In addition I will try to update to 3.2.1

 

[heinzel 0]

I run always in trouble. So I looked closer to the errordiscription.

 

Voila: One little german Umlaut ( an ü) in one of the Materia Settings was the Problem. I changed them to an o , restarted and cura 3.2.1 started without any problems.

No I am going to test the software itself - if everything is working.

 

[DrOldies 0]

Good find! Is this character in settings file or in the code? If you tell me which file I can also do some testing.

[heinzel 0]

It was a setting file in the <configuration folder>/quality/

There I used Materialnames with german Umlaut. So the Filename used asciicoding:

makerbotreplicator_fdmextruder_gal_copperfill%2Bf%25C3%25BCr%2B0.6.inst.cfg

No Unicode? This is odd.

 

But the problem was the content of the value for "name=". It should call "für". But it was like the picture show.

[DrOldies 0]

heinzel - I looked for the makerbotre....insr.cfg and I do not have that file in Cura 3.1 or 3.2. However, 3.2 crashes only with I copy my inst.cfg files into the 3.2 quality folder. I checked each file and found 2 files of 1k in length fulled with NULs. After deleting these 3.2 now loads properly. I looked through by system backup and found the 2 corrupted files as far back as last December. 3.1 apparently ignored them. 

 

I looking forward to trying the new features in 3.2