Jump to content

Ulticontroller Motion no Z axis


mrcdesign

Recommended Posts

Posted · Ulticontroller Motion no Z axis

Hello,

I bought an Ulticontroller, but in the menu i cannot control the Z Axis, is this meant to be?

On the manual i read that you should be able to. Especially when you preheat, there should be more then 1 mm between the nozzle and the bed else you get a blob of plastic.

What should i do?

---

Edit

After searching google some more, i seem to be missing more things in the menu, like "autostart" (but that could be the name) "set origin" "extrude"

 

  • Link to post
    Share on other sites

    Posted · Ulticontroller Motion no Z axis

    Set origin was removed in more recent versions, because it was not desperately useful in most cases. You use prepare -> auto home to find the physical endstops and set the 0,0,0 point.

    Moving the z-axis using the Ulticontroller doesn't always seem reliable in my experience. It can sometimes lead to missed steps (the motor makes a chirp sound, instead of moving completely). Usually this isn't critical, if you just want to get the head out of the way.

    Another alternative that I find useful is to hand-craft a gcode file to move the head to a standard position- e.g., home x and y, and move the head up 20mm from whereever it currently is. I save that in a 'Utility' folder on my SD card, and then, for instance, if I stop a print due to a problem, I can quickly run the gcode from that folder in order to get the head out of the way.

    Finally, I strongly recommend against using the Ulticontroller menu to advance the extruder. It pushes plastic through the nozzle far too quickly, and can cause head blockages. Instead, just turn the big gear by hand (you may need to select Prepare -> Disable Steppers first, or wait a minute for the motors to turn off, otherwise the gear can be hard/impossible to turn by hand). If you turn it by hand, you get a better idea of the rate of feed that the head can handle - you'll start to feel resistance if you turn too fast, and can adjust.

     

  • Link to post
    Share on other sites

    Posted · Ulticontroller Motion no Z axis

    Allright, thanks now i got all the info i need.

    But i dont know how to make Gcode myself. Can you run that Gcode so fast then? doesnt it need to preheat, or what is the trick for that?

     

  • Link to post
    Share on other sites

    Posted · Ulticontroller Motion no Z axis

    No, there's a particular gcode that cause the 'heat and wait' behavior. If that isn't there, it won't heat (or wait). I strongly recommend that you take a look at the gcode that your slicer is generating, and compare it to a reference list like this one, in order to get a feel for how it works. Its really very simple. The only thing to remember is that speeds are in mm per minute (i.e., 60mm/s = F3600), and once a speed is set using an F parameter on a move command, it stays set unless changed, even if it isn't given on subsequent lines.

    That said, here's the code I'm using these days:

    ; Move to home and a relative height of 40mm

    G28 X0 Y0 F3600 ; home x and y

    G91 ; relative position

    G1 Z40 F600 ; move up 4cm

    M84 ; release steppers

     

    It's also included as an attachment, below, that you can copy onto your SD card.

     

  • Link to post
    Share on other sites

    Posted · Ulticontroller Motion no Z axis

    Thanks ill have a look into that.

     

  • Link to post
    Share on other sites

    Posted · Ulticontroller Motion no Z axis

    I also like to move my Z axis by hand whenever possible. It takes about one second. Whereas it takes a whole second just to get my hand to the knob on the UC, let alone push it, rotate to a menu, push it again and maybe a few more times.

    Turning the extruder by hand is even more important. In both cases you can feel if the resistance changes (due to something going wrong with your UM).

     

  • Link to post
    Share on other sites

    Posted · Ulticontroller Motion no Z axis

    Oke, i will do the extruding by hand then. In the Future ulticontrollers will have more buttons for fast access i suppose.

     

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • UltiMaker Cura 5.8 Stable released 🎉
        In the Cura 5.8 stable release, everyone can now tune their Z seams to look better than ever. Method series users get access to new material profiles, and the base Method model now has a printer profile, meaning the whole Method series is now supported in Cura!
        • 5 replies
      • Introducing the UltiMaker Factor 4
        We are happy to announce the next evolution in the UltiMaker 3D printer lineup: the UltiMaker Factor 4 industrial-grade 3D printer, designed to take manufacturing to new levels of efficiency and reliability. Factor 4 is an end-to-end 3D printing solution for light industrial applications
          • Thanks
          • Like
        • 3 replies
    ×
    ×
    • Create New...