On 1/10/2019 at 4:25 PM, jenny8008 said:Important: You have to remove the M104 and M109 commands from the Start-Gcode. These set the temperature of the nozzle and override the settings you've made! (Cura writes the custom temperature before the start-gcode. If this gcode contains another temperature, this second temperature will be set every time.)
jenny8008,
Your settings worked perfectly. I am now able to use Cura on my Alta. Thank you SO much; this will give me so much more control over my prints. Silhouette 3D is just *so* bad at generating supports. I really, really appreciate your help!
- 1
Recommended Posts
Top Posters In This Topic
15
13
8
8
Popular Days
Mar 22
5
Jan 1
5
May 5
5
Jan 10
4
Top Posters In This Topic
jenny8008 15 posts
Mikeyfromindy 13 posts
CU_Ninjaneer 8 posts
GregValiant 8 posts
Popular Days
Mar 22 2022
5 posts
Jan 1 2019
5 posts
May 5 2019
5 posts
Jan 10 2019
4 posts
Popular Posts
tdpspt
Hello Everyone. I just signed up but I am not new here by any stretch of the imagination. I finally feel like I have something worth while to contribute to this ongoin
jenny8008
So, here we are again. These are my Cura-Settings for the Alta: The Start-Gcode: G28 ; home all axes G90 G1 Z5 F1200 G1 X0.000 Y-70.00 F2
jenny8008
Important: You have to remove the M104 and M109 commands from the Start-Gcode. These set the temperature of the nozzle and override the settings you've made! (Cura writes the custom temperature before
Posted Images
jenny8008 5
So, here we are again.
These are my Cura-Settings for the Alta:
The Start-Gcode:
G28 ; home all axes
G90
G1 Z5 F1200
G1 X0.000 Y-70.00 F2000.000
G1 Z0.000 F2000.000
G92 E0
G1 E50.00000 F100;
G92 E0
G1 Z0.400 F6000.000
G1 X-37.984 Y-51.711 F6000.000
G1 E5.99500 F4800.00000
G1 X-36.594 Y-52.712 E6.79005 F540.000
G1 X-33.376 Y-54.825 E7.18850
G1 X-31.774 Y-55.781 E7.22241
G1 X-28.512 Y-57.540 E7.58616
G1 X-26.697 Y-58.422 E7.98434
G1 X-23.446 Y-59.829 E8.04019
G1 X-21.413 Y-60.609 E8.78005
G1 X-18.195 Y-61.684 E8.85674
G1 X-15.980 Y-62.321 E9.57605
G1 X-12.811 Y-63.085 E9.67501
G1 X-10.390 Y-63.561 E10.08386
G1 X-7.329 Y-64.025 E10.37218
G1 X-4.725 Y-64.307 E10.49464
G1 X-1.780 Y-64.497 E10.76990
G1 X-0.510 Y-64.558 E10.90328
G1 X2.780 Y-64.497 E11.16826
G1 X4.725 Y-64.307 E11.31256
G1 X7.329 Y-64.025 E11.56583
G1 X10.390 Y-63.561 E11.72151
G1 X12.811 Y-63.085 E11.96409
G92 E0
And the End-Gcode:
G92 E0
G1 E-40.00000 F2000
G91
G90
G92 E0
G1 E-1.00000 F2400
M104 S0
G28
Link to post
Share on other sites
jenny8008 5
Important: You have to remove the M104 and M109 commands from the Start-Gcode. These set the temperature of the nozzle and override the settings you've made! (Cura writes the custom temperature before the start-gcode. If this gcode contains another temperature, this second temperature will be set every time.)
Edited by jenny8008Link to post
Share on other sites
egyptinside 1
jenny8008,
Thank you so much for this info! I will try these exact settings this weekend, and see how it goes! Thank you again!!
Link to post
Share on other sites