Jump to content

Nylon


jumpmobile

Recommended Posts

I find Taulman Nylon quite difficult to print on my Ultimaker... for a start the diameter tends to be a bit off, so that it often gets stuck in the Bowden. Secondly, the flexible, slippery texture of the surface seems to make it hard for the extruder bolt to grip effectively.

I've done some tests with PA6 Nylon, and that's a little easier to work with. More consistent diameter and plays nicer with the extruder drive, but needs very high temps - 265ºC or more. It'll stick pretty well to the unheated acrylic bed covered in gluestick, especially with lots of brim, but you'll probably want a heated bed for best results with any nylon, as it does tend to warp quite a lot.

 

  • Link to post
    Share on other sites

    I've printed a fair bit of Taulman 618 Nylon on my Ultimaker. The biggest issue is warp. I've had no problems with extrusion or layer adhesion, but warping is a big problem. It sticks great to blue tape, but when it starts to warp it just peels the tape up with it and a heated bed makes no difference. The best thing I've found is to use a big brim and print onto a disposable piece of cardboard. You will destroy the cardboard trying to get it off and generally leave a layer of it left on your print, but it works. Even with this I still find my print warps a little bit though, it tends to bend the cardboard a little....

    The parts don't look particularly attractive, but they are very strong and great for 'engineering' type tasks like pulleys, motor mounts, and brackets.

    Cheers,

    Troy.

     

  • Link to post
    Share on other sites

    I've been printing with Taulman 618. It's awesome as a material-- really strong, flexible, and fairly inexpensive.

    Also, you can print really fast with it without issues. (I've been printing around 80 mm/s)

    The hardest part is getting it to stick to the bed. Heat makes no difference.

    Agree that the thing that seems to work best is craft paper, except you have to make the paper stiff enough.

    Also have tried:

    birch wood (okay)

    sanded masonite board (quite good)

    garolite (didn't work for me)

    I'm going to try glueing the craft paper to the wood

    The other issue is threading. Retraction doesn't work. Actually it prints better without retraction.

    What happens is that nylon 'pulls out', because it is formulated to approximate silk.

    So you get a bunch of threads that are soft and strong...they don't pull off, you need an exacto knife.

    nylon-part-threading.jpg

    I think the threading can be solved.

    Until then, someone should try printing a toothbrush! ;D

     

  • Link to post
    Share on other sites

    Okay, so the biggest problem will be to get it to stick to the bed. So Masonite and gluestick are the first things i will try.

    @Troy: Have you tried printing belt-pulleys yet?

    Thank you all for your the quick and accurate responses. I ordered Taulman 618 ( http://www.mexhibit.ch/#!taulman/cpzy%20)%20and%20will%20post%20as%20soon%20as%20i%20make%20my%20first%20experiences.

     

  • Link to post
    Share on other sites

    Update-- Corrugated cardboard works super well!

    Sand it a little to remove any wax that's on the cardboard surface.

    You'll need a new sheet of cardboard for every print, it sticks that well.

     

  • Link to post
    Share on other sites

    That sounds good....

    Luckily i have lots of cardboard lying around...

    Is the bottom of the prints okay, or is there still cardboard residues on it?

     

  • Link to post
    Share on other sites

    You basically have to tear the print off of the cardboard.

    But if you soak it in water, you can scrub the paper off.

    If you're printing something small, you might get away with using paper tape (sand it first).

    Another update...Finding that retraction helps, but it just doesn't work as well as with PLA.

    So it's probably figuring out retraction settings to work with nylon. Currently it doesn't look like you can make the retraction go faster on the machine settings, but I suppose that might get fixed at some point.

    I'm sure there are people who know how to work with extruded nylon...like from real industrial applications. Insight appreciated!

     

  • Link to post
    Share on other sites

    Hello, nearly one year has passed.

    Any news on this subject like better materials, Cura settings etc ? What type of Nylon should I order to start ?

  • Link to post
    Share on other sites

    I'm pretty sure Taulman "bridge" is the easiest nylon to print. But it might be too flexible for your needs. Here is some data on flexibility and strength of 2 nylons versus other materials:

    http://umforum.ultimaker.com/index.php?/topic/7575-strength-of-different-filaments/

    PA6 nylon is my favorite only because it is less flexible.

     

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • UltiMaker Cura 5.8 Stable released 🎉
        In the Cura 5.8 stable release, everyone can now tune their Z seams to look better than ever. Method series users get access to new material profiles, and the base Method model now has a printer profile, meaning the whole Method series is now supported in Cura!
        • 5 replies
      • Introducing the UltiMaker Factor 4
        We are happy to announce the next evolution in the UltiMaker 3D printer lineup: the UltiMaker Factor 4 industrial-grade 3D printer, designed to take manufacturing to new levels of efficiency and reliability. Factor 4 is an end-to-end 3D printing solution for light industrial applications
          • Thanks
          • Like
        • 3 replies
    ×
    ×
    • Create New...