-
Posts
2,090 -
Joined
-
Last visited
-
Days Won
18
Content Type
Forums
Events
3D Prints
Everything posted by LePaul
-
Bed Temperature not climbing (UMO Heated Bed Upgrade)
LePaul replied to LePaul's topic in UltiMaker 3D printers
Good point I am starting to think this design might be more promising -
Bed Temperature not climbing (UMO Heated Bed Upgrade)
LePaul replied to LePaul's topic in UltiMaker 3D printers
Well the latest attempt with support did a tad better and the bottom looked better So here's the results Now I removed the 3mm nut holding the fan so I could loosen the long threaded rods and turn the print head thinnest side front. I had to loosen the heater/ probe screw to get it moved Trying to maneuver those wires around isn't much fun. ...and it is very clear now that the heater block is very close to where the second fan would be (right side). A PLA housing is going to melt if I attempt to attach it onto those threaded rods I'm a little concerned placing the fan into those threaded screws will suffer the same fate. I didn't really think this through that a second fan is really close to the print head! I'm up for ideas! I'm going to pause here since I can easily go backwards if I need to -
Bed Temperature not climbing (UMO Heated Bed Upgrade)
LePaul replied to LePaul's topic in UltiMaker 3D printers
Trying again....bottom layer back to 0.3 And support -
Bed Temperature not climbing (UMO Heated Bed Upgrade)
LePaul replied to LePaul's topic in UltiMaker 3D printers
Maybe it does need support? -
Bed Temperature not climbing (UMO Heated Bed Upgrade)
LePaul replied to LePaul's topic in UltiMaker 3D printers
-
Bed Temperature not climbing (UMO Heated Bed Upgrade)
LePaul replied to LePaul's topic in UltiMaker 3D printers
-
Bed Temperature not climbing (UMO Heated Bed Upgrade)
LePaul replied to LePaul's topic in UltiMaker 3D printers
Beer helped (thank you Guinness)....and another session of bed leveling. -
Bed Temperature not climbing (UMO Heated Bed Upgrade)
LePaul replied to LePaul's topic in UltiMaker 3D printers
Ugh....so I level bed, adjust knobs during skirt...things look good.... Then first layer, the nozzle starts knocking the first layer items off the bed. Bed at 60 for first layer. Goodness I used to be good at printing. Now every print is a struggle. -
Sad, there's a lot of good information we should make available since the lousy forum software is an epic failure for quickly finding information
-
Well we used to one... Will it return? I know I would love to see something in it's place! For example, others have posted fantastic tips on best printing temps for certain materials, best bed temps with and without glue stick, etc. etc. I would really like to see something like this be available!
-
Dual fan on Ultimaker origonal
LePaul replied to 0235's topic in Third party products & modifications
Okay, so I I want the print head wires facing the back of the printer now. Then...sort out a way to print this shroud and install that fan -
Dual fan on Ultimaker origonal
LePaul replied to 0235's topic in Third party products & modifications
Okay, so a little progress....I found a fan that appears to be the same size as the one that came with my UMO. Nice! Now notice the orientation of my print head....now how can I re-orient the print head? I mean I can unscrew it to the right spot...but where/how do I secure it? I really don't want to take the print head all apart! Essentially I need to swing the printhead around 90 degrees. -
Dual fan on Ultimaker origonal
LePaul replied to 0235's topic in Third party products & modifications
Well you have many more hours of successful printing than me! -
Dual fan on Ultimaker origonal
LePaul replied to 0235's topic in Third party products & modifications
Oh I do a lot of soldering with my Arduino motor shields and R2 work. You should follow my page and see what I do when not sorting out this printer lol I'm calling a local computer shop, hoping they have a 40mm fan I can test with -
Dual fan on Ultimaker origonal
LePaul replied to 0235's topic in Third party products & modifications
See there you go again ,scaring us! Everyone says "just splice in another, works fine!" then a couple threads later, people say not to....I wish Ultimaker or somebody would give a definitive answer on if we CAN splice another fan in safely (with same power limits as first fan) or not. -
Dual fan on Ultimaker origonal
LePaul replied to 0235's topic in Third party products & modifications
I also found a nice part for splicing the wires into each other Snap Lock....forgot i had some of these in my electronics pile! -
Bed Temperature not climbing (UMO Heated Bed Upgrade)
LePaul replied to LePaul's topic in UltiMaker 3D printers
No fan at all through the entire print? I haven't followed the carbon fiber print threads since i figure my printer was less equipped than the U2 -
Bed Temperature not climbing (UMO Heated Bed Upgrade)
LePaul replied to LePaul's topic in UltiMaker 3D printers
Well I am in a vicious loop. If I print XT, I need the heated bed. With my poor cooling on one side, that will fail too Sigh. Ultimaker should just gift me a new printer -
Dual fan on Ultimaker origonal
LePaul replied to 0235's topic in Third party products & modifications
Use gluestick tho at that range for adhesion, right? -
Bed Temperature not climbing (UMO Heated Bed Upgrade)
LePaul replied to LePaul's topic in UltiMaker 3D printers
Yeah, i noticed the bottom of the print looked iffy. It's hard to see silver filament being laid down on a glue coated bed ! I was cranked away on the level knobs to fine tune and couldn't tell if i was making a difference. It may be time to put the Dutch Orange back I have travel speed set to 175, I upped it from 150 Cura 15.04.4. Notice the ducts themselves look horrible...shouldn't need support. But I'm not sure if that's bed heat or what...it looks rumpled. -
Dual fan on Ultimaker origonal
LePaul replied to 0235's topic in Third party products & modifications
Yes, but sadly I can't even get the ducts needed to print acceptably lately. The heated bed has made my life a bit more complicated lately! The link @SandervG gives is for an Ultimaker Oringinal + which has a metal shroud, just so you know. I have the UMO...no + I'm not sure what you have? There's many threads here where there are concerns about the fans you use. I'm not a super experienced electronics guy but from what I can gather, the biggest issue is how many amps you draw. If you make sure the fans are low (as all are), you are fine. There's also some comments about electronic noise, so when the next fan is added, it seems wise to keep those wires clear of the others (heat probe, etc). Here's the model I've been trying to print http://www.thingiverse.com/thing:1268841 As for fans...2-wire is what comes on the UMO. Fans like this look like they would work. I am try to avoid cutting and splicing wires and looking for a Y adapter that would allow two 2-pin wire fans to plug into the one plug. I see 3 wire everywhere but not two. (If you find it, share!) -
Bed Temperature not climbing (UMO Heated Bed Upgrade)
LePaul replied to LePaul's topic in UltiMaker 3D printers
Ever have a day where you want to walk away from 3D printing and say it's just not for you? That's me lately. Here's tonight's botched print. Temp 200 Bed 60C for first layer , then 54 (used gluestick) 40 mm/sec 0.1 layers (Tried cooler and slower to avoid stringing) I'm not sure what to do. Very annoyed. -
Bed Temperature not climbing (UMO Heated Bed Upgrade)
LePaul replied to LePaul's topic in UltiMaker 3D printers
...and to make sure for the UMO....it looks like I want fans that are 2-wire right? -
I think you face a bigger risk with those scented plug ins (the heated fragrance oil dispensers) than a 3D printer going poof.
-
Wait for new models or buy now?
LePaul replied to LesHall's topic in Buying or selling your UltiMaker
What others have said....now's a good time to get the 2+ We don't know what the next version will be and what growing pains will come with it. The 2+ is a pretty sweet machine.