Jump to content
Ultimaker Community of 3D Printing Experts

greens83

Member
  • Content Count

    58
  • Joined

  • Last visited

Everything posted by greens83

  1. greens83

    Max Buid Volume & Brim

    Ok I have a problem with Brim. I have an upside down cone shape to print, the top of the cone is just within the max build volume, the bottom is only 20mm diameter or something. My problem is I cant use the brim setting without having to shrink the model, which I dont want to do. Im assuming the brim setting adds the brim width to you models max dimensions. It should really add to the first layer max dimensions to avoid restricting build volume on models larger at the top than bottom. Is there anyway around this that anyone knows of? Thanks in advance for any input.
  2. I recently bought a second hand UMO on ebay. Its not in great condition, belts are all stretched and it probably need stripping down cleaning and re-assembling. I don't mind doing this as is was quite cheap in the end. I still have the UMO I bought 5 or 6 years ago with a heated bed upgrade kit and the ulti controller both of which are no longer for sale as upgrades which is disappointing. So with that in mind I got to thinking about a heated bed chamber instead of a heated bed and here's where I'm hoping fellow makers can give me an opinion. Can a heated chamber replace a heated bed? If I heat the chamber to 60 degrees is that just as good or perhaps better than a 60 degree bed? Id like to use this machine for printing more exotic materials like PC, PP and nylon. I have had some success with my other UMO+ printing these materials by enclosing the chamber. Ill also be looking at replacing the hot end with one from E3d. Any opinions and advise welcome. P.S. Does anyone know where I can find a good set of instructions to make a 3rd party Ulti controller (or even better know anywhere that has stock)?
  3. greens83

    UMO heated bed vs heated chamber?

    Thats good to know about the ulti controller, thanks for the info. I guess its down to the heat directly transferring from the bed to the print rather than the whole chamber being that temperature? Looks like Ill have to find some 3rd party heated bed builds. thanks again. Jamie
  4. Is this still for sale?
  5. greens83

    Fan off at height?

    Fellow ultimakers, Ok I might be missing something here but I cant figure out how to turn the fan off at a certain height in Cura. I know it can easily be turned on at a certain height or layer but I want to do the opposite. I'm printing some Colorfabb HT and the bigger layers are higher up (think inverse pyramid) so warping becomes an issue. I still need cooling on the lower layers though. I've done it manually and it prints nicely but Id love to be able to just leave it going knowing the fan will turn off. Any ideas? Thanks in advance for any suggestions.
  6. Fellow UMers, I'm considering upgrading my UMO with an E3D V6 hot end with the volcano pack so I can print hotter and faster with wider nozzles and other materials. I'm very confused as to what I actually need to order though. I upgraded my UMO with the heated bed and so it has a 24v PSU. SO I'm assuming I order the 24v E3d V6 version? Then I assume I need to print a mount for it. Is it this simple or am I missing something? Even though the PSU is 24V will the UMO board ouput 24V to the heater cartridge? Any advice very much welcome. Jamie
  7. Thanks for the info, very much appreciated! Ill check out your how to for the bypass.
  8. Fellow Ultimaker gurus, Does anyone have any experience with this upgrade ? http://3dgbire.com/products/extrusion-upgrade-kit £400 is quite a price tag, Im wondering whether its worth that much and how much it could improve my prints. Any thoughts/opinions appreciated. Thanks in advance, Jamie
  9. greens83

    Build Volume Restricted

    Hello fellow UM'ers, I am trying to print a cut down spherical lampshade on my UM2 that measures 220mm (max dia) by 156mm high. For some reason Cura will only let me print it at 195mm dia. I checked the build volume settings in cura and they are the default size (larger than my object). I cant understand why Cura wont let me print at 220mm. Any suggestions welcome. Thanks in advance, J
  10. Assembled Original Ultimaker for Sale in UK !! £ 7 5 0 / € 9 5 0 !! 19 months old. Fully assembled and callibrated. It prints very well. Lots of printed improvements (see below). New hot end fitted as I managed to break a thread when I over tightened after cleaning. Ill also include a close to full roll of black fabedashery PLA (Ive found this to be the best PLA). FOR SALE: Ultimaker Original with Ulti-controller and V2 Hot end. Adjustable LED lighting integrated into Ultimaker Printed carry handle Printed extruder gear Printed Bowden clip circlip to improve retraction Printed belt tensioners Images of the machine: Recent prints: Its served me very well and Ill be sad to see it go. I have bought new ultimaker 2 and don't need 2 printers. I will accept £750 /€950. Thanks Jamie.
  11. greens83

    UM1 for sale UK

    Nancy, Ive decided to keep the UM1 for experimenting with new materials. Sorry for any inconvenience. I hope you find one soon.
  12. greens83

    UM1 for sale UK

    Hi Nancy, Yes it is still for sale. No it doesn't include a heated bed. Jamie
  13. Assembled Original Ultimaker for Sale in UK !! £ 6 9 5 / € 8 8 5 !! 19 months old. Fully assembled and callibrated. It prints very well. Lots of printed improvements (see below). New hot end fitted as I managed to break a thread when I over tightened after cleaning. Ill also include a close to full roll of black fabedashery PLA (Ive found this to be the best PLA). FOR SALE: Ultimaker Original with Ulti-controller and V2 Hot end. Adjustable LED lighting integrated into Ultimaker Printed carry handle Printed extruder gear Printed Bowden clip circlip to improve retraction Printed belt tensioners Images of the machine: Album: Ultimaker for Sale 7 images 0 comments Recent prints: Album: UM 1 Prints 8 images 0 comments Its served me very well and Ill be sad to see it go. I have bought new ultimaker 2 and don't need 2 printers. I will accept £750 /€950. Thanks Jamie.
  14. Hi Thirty six. I am indeed in Leeds. Are you still interested in buying my UM1 ?
  15. Hey fellow UM'ers just thought Id share this little tip. I had a few blockages with both my UM1 and UM2 in the past, I always wondered 'how is material getting into the nozzle to cause blockage?' So I took a small piece of sponge material, and pushed the filament through it before it goes into the extruder, then attached it to the extruder with a rubber band. This means it it cleans the filament as its pulled up into the extruder. No blockages since ! I've had this little mod on both my UM1 and UM2 for 2 months now and done a fair bit of printing so I do think its working ! (UM1 is for sale in the for sale section If anyones interested !) http://umforum.ultimaker.com/index.php?/topic/7469-assembled-original-ultimaker-for-sale-in-uk-%C2%A3-7-5-0-%E2%82%AC-9-5-0/
  16. Interesting, Id not considered that. What is 'Roberts feeder' ?
  17. greens83

    UM 2 Temperature ?

    Hello fellow U.M.ers. I got my new UM2 this week after 2 years using the UM1 (which I still love!) One thing that's troubled me slightly is I don't have the option to change the temperature in CURA for my UM2. Can someone fill me in on : 1. Why the temperature settings have gone ? 2. How is the temperature determined If I'm not setting it ? (I really hope its doing something intuitive based on the rest of the settings and printing at the lowest sensible temperature !) 3. Is there a way to set it manually If needed ? Thanks in advance for any insight into this !
  18. greens83

    Responds time of the support?

    I had a question about my order for a spare part too. I got a reply saying that they had contacted the logistics department but didn't have my order number so couldn't get any information. The order number was in the title of the e-mail, including the one they sent back to me stating they didn't have the order number....
  19. Ive just seen the ultimaker 2 has been released and read the info. My question is does the ultimaker 2 produce better quality prints than the ultimaker 1 ? I can see the heated bed is a big plus, but are the other components used enabling better prints ?
  20. greens83

    Ultimaker 2 vs Ultimaker 1

    Any more opinions on this subject now the UM2 has been out a bit longer ?
  21. I had a lot of trouble putting fabadashery filament on the ultimaker spools until I tried doing it on a broom handle(running through reel and spool centres), it takes a bit of time but it fits on there and the broom handle keeps it from tangling (it still kind of birds nests but If you gently spin it the opposite way your winding it on it goes back to a manageable reel).
  22. More images of prints from this printer.
  23. Original Ultimaker for Sale in UK 13 months old. Fully assembled and callibrated. It prints very well. Lots of printed improvements (see below). Ill also include a close to full roll of black fabedashery PLA (Ive found this to be the best PLA). FOR SALE: Ultimaker Original with Ulti-controller and V2 Hot end. Adjustable LED lighting integrated into Ultimaker Printed carry handle Printed extruder gear Printed Bowden clip circlip to improve retraction Printed belt tensioners Images of the machine: Images of a recent print: Its served me very well and Ill be sad to see it go. I am selling to buy a new ultimaker 2. Sensible offers/Questions please message me. Thanks Jamie.
  24. greens83

    MAKE 3D Printer Test...

    I hear you, I'm excited about predictions in lots of new SLS machine coming out now key patents are up but the build volumes of the current offerings un 5k are far too small for me. Maybe next year..... Its looking like a UM2 for me. Just need to sell the UM1 to part finance it (in the for sale section If anyone's interested) Ill be sad to see it go but I'm hoping there'll be a small step up in print quality and a bit less time spent maintaining and tinkering with the machine.
  25. greens83

    MAKE 3D Printer Test...

    I certainly prefer the ideals of Ultimaker, and I have been very happy with the UM1, the support I've received and the help and advise Ive had on these forums. But ultimately I want the best quality 3D prints possible within my budget. This is why I was so disappointed with the MAKE reviews this year, because all I have to go on is the sentence at the end of the UM2 review saying it has some catching up to do, which I'm not convinced is true. The build volume of the UM2 is probably going to be the clincher anyway.
×

Important Information

Welcome to the Ultimaker Community of 3D printing experts. Visit the following links to read more about our Terms of Use or our Privacy Policy. Thank you!