Smithy
-
Posts
5,666 -
Joined
-
Last visited
-
Days Won
147
Content Type
Forums
Events
3D Prints
Posts posted by Smithy
-
-
Danke fürs Update.
Das ist allerdings komisch, aber gut, dass es jetzt funktioniert. Möglicherweise ist da irgendetwas mit den Druckerprofil passiert. Durch das Neuanlegen wird das Profile ja wieder neu erzeugt.
-
Hi,
they are only similar on the first sight, but the S5 has much more:
- The S5 has hardened feeder weels so you have the ability to print abrasive material with the new CC print core.
- Improved auto-leveling, which measures the whole build plate and not just 3 points as the UM3
- Bigger build volume, you can never have enough room for your prints 🙂
- Modern touch display
- Filament sensor
- Better feeder, which is a charm compared to the UM3
- and some other improvements
If you have the budget, go with the S5, it is more future proof (there is an extension port, which is reserved for ??? extensions) and you have much more possibilities like build volume and the ability to print abrasive materials.
On the other hand, if you have a smaller budget, you make nothing wrong with the UM3, it is still a great printer, except for the differences mentioned above.
-
As far as I know, there is no possibility, except manual editing the gcode, to pause the print in the kind you need it. There is a plugin to pause at a specific layer, but you would need it in the same layer.
You can just go through the gcode and add the pause manually where you need it, but I am not the gcode expert and don't know the command or sequence you need for that.
-
Hi
I guess you have one or more hardware issues, like belt tension, z screw, general stability, or something like that. But here are not so many users with Prusa printers, so I am not sure if someone can point you in the right direction. I can also not say if it is normal, that the bed leveling is normal for your kind of printer.
I don't think that it has something to do with Cura, but if you check the layer view in Cura and don't see any problems, then the file was sliced correctly.
-
Looks nice, thanks for sharing...
-
Du könntest noch das das ganze Projekt in Cura speichern (als Projekt) und hier uploaden, dann sehe ich auch deine Settings die du eingestellt hast.
-
Yes, that's right, switching to Marlin gives you full control.
With Ulticode flavor the material is managed by the printer and you have to edit the materials.txt file to add new materials or change parameter.
-
1
-
-
Also am STL bzw. deinem Fusion Object liegt es nicht. Ich habe das STL geladen und in Cura 3.6. importiert und es schaut gut aus. Musste es nur runter skalieren, weil es kanp 400x400mm groß und 10mm dick war, aber sonst passt es.
Ich hab dir das STL auf deiner Datei hier auch nochmal angehängt, vielleicht klappt es damit.
-
To be honest, I don't know and I was just guessing it could be the fan. It looks as under extrusion, but I have no idea why it is only on one side.
You could also try to rotate the object by 90° to see what happens.
-
I expected a little bit more details and I missed the "how to" of the title, but it was nice an had a very professional touch.
I thought we will get some info about how to setup Cura, are there some settings which are important to switch on/off and so on. But on the other hand, that would not fit into 30 minutes, so maybe I had the wrong expectations.
But anyway, it was good and I am looking forward to the next webinar.
-
-
Hallo
ich vermute das Problem schon beim exportieren. Ich nehme an, du gehts zum Exportieren auf Erstellen -> 3D Druck in der Menüleiste oben? Dann wählst du das Object aus, ist das dann noch so wie du es gezeichnet hast? Weil in Fusion kommt es auf deinen Workflow an, ob du einen oder mehrere Bodies hast.
Ich vermute, dass du die Schiebe schon so exportierst ohne es zu wissen.
Du könntest in Fusion auf einen öffetnlich Link auf eine Datei erzeugen und mir schicken, dann kann ich mir das ansehen wenn du willst.
-
Hi
it looks like under extrusion, but why only on one side? So I guess it is not under extrusion, but maybe your cooling fan is blowing too much cool air on this side and you get some kind of warping of the layer itself before it can get bonded to the previous layer.
Check if you fan, I think the A8 has only one, is on that side. If so try to decrease fan, 75% is normally too much for ABS, turn it off completely or try around 10% fan speed.
That said, printing ABS without an enclosure is very difficult to not possible. You need an enclosure around your printer to keep the warm air inside.
-
But cool, like a spaceship command center 🙂
-
Strange, it still looks like you are printing too hot, but you are already 10° lower than the profile suggests. You can again try to print cooler until you get under extrusion and then increase it again about 5°. But usually the material profiles for UM material are ok, without the need to tune something or not it such a massive way.
The zits on the outside are more less normal, this is the z-seam, but the layer itself looks "melted".
What about if you print something else, a cube for example - can you try it?
And do you still print with the default profile settings, except print temperatures? If not what else have you changed?
I can also help if you can upload your Cura project file here.
-
UM has a nice studio, like a newsroom 🙂
-
Du kannst auch 0.6 einstellen, Cura stellt seit einiger Zeit bzw. beim UM3 7/8 von der Nozzle Size ein, weil das angeblich ein besseres Ergebnis bringen soll. Deswegen steht die Line Width beim 0.4er Core auch nicht bei 0.4 sonder bei 0.35.
Ob es wirklich einen Unterschied macht, weiß ich nicht.
-
Great idea, thanks a lot 🙂
-
1
-
-
Ok, next try with 220° and set additionally minimum layer time to 10s if you print just these two pieces, to give the previous layer more time to cool down.
-
-
It is better to use the same speed settings for walls, infill, ... so set everything (should be 6 settings) to the same speed. Then it should be faster because 15mm is very low and the quality should be better. Set it to 30mm or 35mm/sec.
And flow 80% is not good in my opinion, it is better to leave it at 100% and reduce a little bit the temperature if you need it.
And post a picture please, that we can see how it looks.
-
1
-
-
haha, what a massacre and because she cried too much, you put her, head over, into the acorns...
-
1
-
-
A new Cura version is currently not available, also not an official beta.
Will a beta be available soon? Maybe....
-
Nein, da gibt es nichts zu kalibrieren und auch kein Offset, aber dein Problem sollte lösbar sein, denn es gibt sehr sehr viele UM2 mit Olsson Block die ohne Probleme drucken.
Mir fallen spontan 3 Dinge ein, die als Ursache in Frage kommen:
- Die Heizpatrone und/oder Temperaturfühler sind nicht korrekt im Olsson Block drinnen. versuche einmal ob die noch weiter rein gehen bzw. sieht man es vielleicht hinten wenn noch zuviel raus schaut.
- Die Lüfter kühlen den Block zu sehr und dadruch kommt er nicht auf Temperatur. Normalerweise kommt da aber dann irgendwann einmal ein Heater Error, besonders bei den ersten paar Layern. Schau mal auf Youmagine da gibt es etliche Modifikationen für die Lüfter um dieses Problem zu umgehen.
- Du hast vielleicht gar kein Heizproblem, sondern eine verstopfte Düse oder ein Problem mit dem PTFE Coupler.
Geringe Temp. Abweichungen können schon sein, aber von 210 auf 260 ist ein bisschen gar viel, da hats was....
Please Slice and Post!
in UltiMaker Cura
Posted