Jump to content

Printcore 2 height problem


ideszcsu

Recommended Posts

Posted · Printcore 2 height problem

Hi there.I´m having some troubles with my last printings and i´ve realised that the printcore 2, even when the lift switch is up, remains lower than printcore 1. Now appears the "Difference between detected height of both PrintCores exceeds realistic values" error. However this is an usual error for me.

The problem is that I cannot level the platform cause printcore 2 is always lower than printcore 1

Any ideas? Could it be a problem with the spring? I feel it isn't working well when I do this and the lift switch seems to work fine:

grips.jpg

I´m using Ultimaker 3 extended

Thanks

  • Link to post
    Share on other sites

    Posted · Printcore 2 height problem

    Instead of just using one hand, try using the other hand to squeeze from the nozzle to the clear part.

     

    Slide it up and down many times.  Where is it sticking?  The spring can get jammed and start to come out of the clear part.

     

    Taking the clear part and spring off is easy.  Try doing that and putting it back together.  Here is a detailed video of taking your core apart but you only need to remove the clear part so it's quite simple.

     

    Full disassembly is really a last resort and can destroy your core but taking off the clear part is simple.

     

     

     

  • Link to post
    Share on other sites

    Posted · Printcore 2 height problem

    More likely I'm thinking something is broken in your UM3 print head.  Try putting other cores into the right side.  Do they go up and down when you slide the lever?

     

    • Thanks 1
    Link to post
    Share on other sites

    Posted · Printcore 2 height problem

    Thanks. I´ve tried to disassemble just the clear part and the spring looks good. Just the black piece is a little bit loose, but this only affects when you load the printcore right? when the printer is working the black piece is unusefull.

    The print head also looks good. I have no idea what is happening. So I attach two pictures with the lift switch up and down. Maybe you can see what is wrong here. (I know it's not the cleanest print head 😅)

    Thank you so much

     

    IMG_20190917_101014.jpg

    IMG_20190917_101024.jpg

  • Link to post
    Share on other sites

    Posted · Printcore 2 height problem
    On 9/16/2019 at 6:55 PM, gr5 said:

    More likely I'm thinking something is broken in your UM3 print head.  Try putting other cores into the right side.  Do they go up and down when you slide the lever?

     

    Any other idea?

  • Link to post
    Share on other sites

    Posted · Printcore 2 height problem

    HI,

    Reviving an old post on a similar issue rather than create a new post.

    I bought a fairly well used UM3 extended last week

     

    It had a broken wire to the capacitive sensor (now re--soldered back on)

     

    Once reattached, I am now getting the 'realistic height error'  during levelling.

    There was a physical difference in the dimensions of the two print cores when I took them out of the printer, the heatsink and lower thread had partially unscrewed. 

     

    When looking for further options for repair, I came across this page.
    https://www.dynamism.com/learn/3d-printing/ultimaker-error-codes-and-solutions.html

     

    All the other links work, but the 'realistic height error' link goes to a SalesForce splash screen.

    Does anybody know what content is on this page for error checking?

     

    (have done the following:

    cleared print heads using hot and cold pull

    ensured print nozzle is clean externally, wire brush and wipe with rag

    dropped bed to lowest level, then unscrewed three turns

    manual adjust first.

    )

     

    Open to any further ideas,.

     

    Regards.

     

    A

  • Link to post
    Share on other sites

    Posted · Printcore 2 height problem

    Article your looking for should be this one: https://support.ultimaker.com/s/article/1667410781005
    Not sure why they built a knowledge base against a different websites knowledge base though, thats odd..

    Print cores are technically considered not serviceable by UltiMaker.
    They should be the same length, if not your just always going to have issues as there is no way to adjust the z offset between them.

  • Link to post
    Share on other sites

    Posted · Printcore 2 height problem

    Thanks Dustin,


    After posting, I also realised that the wayback machine would have the original article also - they're both as detailed.

     

    A

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Introducing the UltiMaker Factor 4
        We are happy to announce the next evolution in the UltiMaker 3D printer lineup: the UltiMaker Factor 4 industrial-grade 3D printer, designed to take manufacturing to new levels of efficiency and reliability. Factor 4 is an end-to-end 3D printing solution for light industrial applications
          • Thanks
          • Like
        • 3 replies
      • UltiMaker Cura 5.7 stable released
        Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
         
          • Like
        • 26 replies
    ×
    ×
    • Create New...