Jump to content

Securing an Ultimaker - shock absorbing feet or solid anchor?


Recommended Posts

Posted · Securing an Ultimaker - shock absorbing feet or solid anchor?

Good afternoon everyone.  I hope this finds you and yours well.

 

Like many here, I'm pushing my printers to supply the front line.  Watching my better half don her scrubs and head into the clinic is a powerful motivator.

 

Speed is important but so is accuracy, so I am looking at ways to improve.

 

There are many mods that aim at reducing the translation of shaking from rapid moves into the table or as noise.  Looking at my CNC bed, the solution there was the opposite.  Go as heavy as possible on the supports and immobilize the base. It was even suggested that we fill the aluminum extrusions with concrete or sand to add weight and inertia.

 

So back to my UM3.  I am thinking the box is pretty rigid, but perhaps it could be more so.   I'd like to hear your thoughts on the base and ways to mitigate vibration and shaking.

 

Thanks and stay healthy!
 

John in Ottawa.

  • Like 1
Link to post
Share on other sites

Posted · Securing an Ultimaker - shock absorbing feet or solid anchor?

Hi John,

 

Great to hear!

 

What you say here is something I’ve been looking to for a long time.

I’ve reduced the extruder weight as much as possible (an UM2) in order to reduce the force during acceleration / deceleration. However, the printer still vibrate..

 

Can remember, some time ago, that @Daid said some people put the printer upside down in order to have some special print perfect.. Hmm..

 

Next I’ll thinking to do is to make the anchor fixture for the printer at the level where the main shaft are located. This anchor armature will be into a solid table plate that will absorb lot’s of the head’s impact of vibration. Maybe not very practical thing to have on a desk, but will improve for sure. 🙂

 

Another thing, @burtoogle asked in here if someone is interested in vibration analysis for 3D printing. (I am.) I’m thinking here, -analysis of a given object to print in order to have best possible print -by have an automatic speed and accelerations at any time of printing (or during slicing?).

 

Well, burtoogle is making “vibration, tracking and spectrum analysis systems” for the aviation, so if there is anyone that can handle this, he can!

 

In this time, take care everyone.

 

Thanks

 

Torgeir

  • Link to post
    Share on other sites

    Posted (edited) · Securing an Ultimaker - shock absorbing feet or solid anchor?

    Hi,

    I think the truth lies in between: having a sturdy solid table to put the UM3 on it, and using some rubber feet (like for example these: www.thingiverse.com/thing:3059433 ) will do the trick.

    Regards

     

    ...and id could be a good idea checking the frame screws for tightness, as they also can come loose by vibration and time (I wonder why this is missing in the official maintainance shedule)

    Edited by Enigma_M4
  • Link to post
    Share on other sites

    Posted · Securing an Ultimaker - shock absorbing feet or solid anchor?

    Before I upgraded my stepper drivers on my UMO, I added some rubber feet made from automotive heater hose.  It was what I has on hand and it made the printer much quieter.  A difference in print quality was not noticed.  I printed some simple cylinders with a through hole for mounting.  The OD is a slight press fit for 1 inch hose.  Screwed them to the bottom.  Pushed on 4 pieces of hose somewhat longer than the spacers.

  • Link to post
    Share on other sites

    Posted (edited) · Securing an Ultimaker - shock absorbing feet or solid anchor?

    Hi..

     

    Yes, been using kind of same method, as a 1/2 inch thick "hard foamed" plastic (the withe one..) between the table and printer for a long time. However, as it become compressed over time it has to be renewed, -the kind I'm using.  But it is insulate the bulling noise that's amplified when in direct contact with the table.

     

    What I'm think about is a kind of "active vibration" system, that's sensing "hi impulse" movements that's make the build plate vibrate, I.E. when doing infill etc. IMO., there is two approaches to solve this, by doing it "almost" in real time or by analysis of the gcode file before printing, in order to adjust speed according to a known speed/movement table before printing -for this printer, or printer type..

     

    Here is an example of a system that can measure vibration in X,Y and Z axes, using an accelerometrer ADXL326 and an Arduino compatible microcomputer, a Teensy 2.0 using an Atmel AVR microprocessor.

     

    1006577261_Teensy2_0.thumb.jpg.3ca931b34529dcbcc93b230f97fe8eea.jpg

     

      This is actually the hardware that could be used as a start..

     

    Take care

     

    Thanks

     

    Torgeir

    Edited by Torgeir
    Txt error.
  • Link to post
    Share on other sites

    Posted (edited) · Securing an Ultimaker - shock absorbing feet or solid anchor?

    I have used these for about 2+ years and have found them to work very well on my UM2+ - certainly reduce the noise etc. Design by @UbuntuBirdy who used to be on here.

    https://www.youmagine.com/designs/ultimaker-2-2-damper-feet-12-55

     

    I assume they would work on a UM3, but would be worth checking the dimensions of the grooves on the mounting area.

    Edited by navigator
    Added designer info.
  • Link to post
    Share on other sites

    Posted (edited) · Securing an Ultimaker - shock absorbing feet or solid anchor?

    I've been using Sorbothane viscoelastic rubber half-spheres as dampening for my Ultimakers for years, and it really does reduce the noise quite a bit, with my own designed feets:
    https://www.youmagine.com/designs/dampening-feets-for-ultimaker-2-3

    carousel_Sorbotame_feet_v5_2.png

    Edited by meduza
  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • UltiMaker Cura 5.8 Stable released 🎉
        In the Cura 5.8 stable release, everyone can now tune their Z seams to look better than ever. Method series users get access to new material profiles, and the base Method model now has a printer profile, meaning the whole Method series is now supported in Cura!
        • 5 replies
      • Introducing the UltiMaker Factor 4
        We are happy to announce the next evolution in the UltiMaker 3D printer lineup: the UltiMaker Factor 4 industrial-grade 3D printer, designed to take manufacturing to new levels of efficiency and reliability. Factor 4 is an end-to-end 3D printing solution for light industrial applications
          • Thanks
          • Like
        • 3 replies
    ×
    ×
    • Create New...