Jump to content

layershift when printing small miniatures' legs


Recommended Posts

Posted · layershift when printing small miniatures' legs

asset.JPG

 

 

I am printing somefairly small miniatures and their legs always give me headache for printing.

The above image shows the layer shift on the legs.

 

 I am using UM3 with PLA, most of the time my prints are fine but when it comes to small things and structure like this it seemed to fail.

The adhesion is okay, but after a while the nozzle started to sort of knock the legs around a bit causing a layer shift during print.

 

I have been printing slow at 30mm/s.

I have checked the belt and they are tight.

I have done manual leveling on buildplate just in case.

Switching materials(brands) doesn't seem to hv differences, and this is some good eSun filament.

 

none of the above action help.

So I am going to show you how i slice my STL, see if i done sth wrong there.

 

image.thumb.png.938b3de90dd2aa735b710c31d0392c95.png

 

image.thumb.png.82b0d0b096ba75377eaee64684f756d8.png

 

I have tried different ways and both still have layer shift issues.

The first one with support interface enabled, support enabled, support brim enabled, tree support enabled, and increased 40% support density.

The nozzle would knock on the printed legs and cause layershift mid-way, usually on one of the legs.

The second one is on same settings but with a manually added cube printed as support.

This one has less major layershifts but lot of minor shifting along the print, the result is shown in the first photo.

 

Any good advice?

 

  • Link to post
    Share on other sites

    Posted · layershift when printing small miniatures' legs

    Have you tried designing a custom brim in the CAD file itself, and maybe some sort of tree-like or inverse-tree supports? Just to add more stability? I guess it now starts wobbling around due to the brim or supports not being stiff enough?

     

    An added issue could be not enough cooling, due to the hot nozzle sitting continuously on a small area, which tends to increase this sort of effects. So, adding a dummy cooling tower or printing multiple at once might improve this. But it might also worsen the situation if during traveling around, the nozzle would hit the legs...

     

  • Link to post
    Share on other sites

    Posted · layershift when printing small miniatures' legs

    I don't see the layer shift.  The legs seem to match the view from cura.  Can you point an arrow very accurately to exactly the problem spot?

     

     

  • Link to post
    Share on other sites

    Posted · layershift when printing small miniatures' legs

    I still don't know what you are talking about.  Can you show one with "shifting" and one without?  Usually when people talk about shifting it's a problem where a stepper misses a step and the entire part shifts to a new X or Y location such that the bottom half doesn't line up with the top half.  LIke this:

     

    https://support.3dverkstan.se/article/23-a-visual-ultimaker-troubleshooting-guide#shifted

     

  • Link to post
    Share on other sites

    Posted · layershift when printing small miniatures' legs

    image.thumb.png.50cc826245abd6f8f050f804e0ceae3f.png

    i have thrown away some more obviously layer shifted ones. but in the photo  there's a layer where up to a point the print  shifted a bit to the right. this usually happens when printing two-leged models from bottom up, perhaps somehow the nozzle knocked the print a bit and the two towers doesnt match up at some point and show shifting. Printing slower somehow prevent this from happening

    image.png

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • UltiMaker Cura 5.8 Stable released 🎉
        In the Cura 5.8 stable release, everyone can now tune their Z seams to look better than ever. Method series users get access to new material profiles, and the base Method model now has a printer profile, meaning the whole Method series is now supported in Cura!
        • 5 replies
      • Introducing the UltiMaker Factor 4
        We are happy to announce the next evolution in the UltiMaker 3D printer lineup: the UltiMaker Factor 4 industrial-grade 3D printer, designed to take manufacturing to new levels of efficiency and reliability. Factor 4 is an end-to-end 3D printing solution for light industrial applications
          • Thanks
          • Like
        • 3 replies
    ×
    ×
    • Create New...