Jump to content

make cura faster...


david-ganon

Recommended Posts

Posted · make cura faster...

hi guys, i was thinking:

what if cura could give you the option to choose one layer height for the outer shell and different one for the fill and support.

the resolution is very important for the outside of the model, but not for everything else.

so lets say the head prints in 0.05 res the outer shell, and after 4 layers it prints the fill and the support in 0.2 res.

it can do this !!!

tell my what you think :)

 

  • Link to post
    Share on other sites

    Posted · make cura faster...

    Daid made some tests a few months ago for having the outer shell drawn in smaller layers and then the inner shell and the infill with significantly larger layer height. However, he decided not to implement this feature. So, if you want this feature, you would have to write it yourself... ;)

     

  • Link to post
    Share on other sites

    Posted · make cura faster...

    NetFabb can do this too, though NetFabb is no longer supported or reccomended... I paid for the comercial NetFabb years ago when it was the reccomended comercial option for UM (and the only alternative at the time was Skeinforge). NetFabb is now way behind in most areas and hasn't received any updates for it's Ultimaker support in well over a year... but although I use Cura for most things I still fall back on NetFabb for high quality prints.

    Cheers,

    Troy.

     

  • Link to post
    Share on other sites

    Posted · make cura faster...

    I'm still a bit pissed about having spent so much money on Netfabb. Sure, at the time it was the best available, but it quickly became run over by the competition and then they just stopped updating it.

     

  • Link to post
    Share on other sites

    Posted · make cura faster...

    This is a difficult problem in slicing. Most slicers probably implement this by drawing the exact same outer perimeter twice. But it would be better if it followed the contour of the part you are slicing.

    But following the part shape means the two skin layers are quite different - or can be. So where to you put the infill? Where the upper layer is? Or the lower? Or half way between?

     

  • Link to post
    Share on other sites

    Posted · make cura faster...

    I know KISS does not simply stack at least. I'm not sure which dimension it goes off of when doing the infill though. Not sure how slic3r does it as I haven't used it very much. IIRC Netfabb followed the contour as well but I haven't used that for years so I'm not 100% sure. Skeinforge used the cheat of just stacking two half height layers directly on top of each other.

     

  • Link to post
    Share on other sites

    Posted · make cura faster...

    Daid made some tests a few months ago for having the outer shell drawn in smaller layers and then the inner shell and the infill with significantly larger layer height. However, he decided not to implement this feature. So, if you want this feature, you would have to write it yourself... ;)

     

    No, I decided that my implementation was crappy (hacked together) the idea still works, but I need to do it better.

     

  • Link to post
    Share on other sites

    Posted · make cura faster...

    No, I decided that my implementation was crappy (hacked together) the idea still works, but I need to do it better.

     

    Oops, sorry... :oops: I should check what other people have really written before writing just some nonsense... :roll:

    To my defense: We have 34°C today... B)

    @David Ganon: So there is still hope...

     

  • Link to post
    Share on other sites

    Posted · make cura faster...

    Oops, sorry... :oops: I should check what other people have really written before writing just some nonsense... :roll:

    To my defense: We have 34°C today... B)

    @David Ganon: So there is still hope...

     

    No problem. Hot weather can be a bitch.

    This feature is somewhere on my roadmap, but I have no idea when.

     

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Introducing the UltiMaker Factor 4
        We are happy to announce the next evolution in the UltiMaker 3D printer lineup: the UltiMaker Factor 4 industrial-grade 3D printer, designed to take manufacturing to new levels of efficiency and reliability. Factor 4 is an end-to-end 3D printing solution for light industrial applications
          • Thanks
          • Like
        • 3 replies
      • UltiMaker Cura 5.7 stable released
        Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
         
          • Like
        • 26 replies
    ×
    ×
    • Create New...