BiMNrd

They should be keeping in contact with us and with their reseller channels contantly. I bought the S5 because of the pro bubdle, otherwise I would have gotten the S3 and we aftermarket parts.. And estimated ETA would be good, or at a min, send the unit with the caveat that an firmware update is to come.

USA, I don't even think ultimaker knows when at this point to be honest uh?

I am unable to get an e-mail response from my vendor in regards to my order, so I wanted to know if the Air manager is already shipping or what is the ETA. I have paid in full for the device since it was announced. Thank you @SandervG any ideas?

Oh wow..

I get it, no bashing. I can wait till my HT arrives next week. I ordered black. Ill post something on there for comparison if you dont mind.

Great, I hate how real printed part dont look anything like the marketing stuff in terms of finish. Maybe also be the "Clear" I am not a fan of that color in FDM printers. Otherwise this is great info my friend and seems to be a success for you.

Is that the colorfab HT ?

^yes NylonX is cabon reinforced. UL has a profile for it in cura. I ordered some to try. I will print something small and see how it holds up.

Thanks for sharing that material. I followed you lead and ordered some HT. Apparently you don't need a harneded nozzle for it - which is great. I also did order some nylonX. I wonder how that would do as a front bumper cannard. (Exposure to sun, heat, water if it rains)

so then, it may not work in an engine bay where it may get wet or exposed to water and our moisture. maybe I am betting off with Polycarbonate.

I know, but I found you can make support be created with multiple lines if needed to make the parts stronger. I need to make a support to hang an oil filter relocation adapter. I am sure the item will get hot since it is alum. looking at this thread, and considering Nylon flexes, I wonder it Polycarbonate would be better (considering nylon is flexible - from what I saw on this thread).

yeah, but would be great just do this on holes.

Great post. how long this this take to print?

Great thread, so are you guys modeling your down reinforcement inside the 3d part? for example, how can I thicken the walls around the holes? I know other mfr. slivers allow for this, bit its proprietary to their product. BTW, I want to know about the internal watermark. Doesnt that type of think make the STL exporting more difficult and cause issues? I always though we wanted clean watertight geometry.

I would call it under extrusion. try that. what printer, material and settings are you using?

3d printing?? hehe.

Can you link me to this? how long? I have pre-paid for the equipment ,but if I am not going to get it anytime soon I rather cancel and order in the future.

A few things need to happen and I will do. 1. The camera needs to be accessible via WAN. P2P? Im going to install a network camera to my printer for this. 2. We need to be able to stop a print remotely. 3. Im going to remake the cameras adapter to aim the camera in what I consider a move usuable angle. I had some new RE software I want to try for this along w my scanner. Should be easy.

Would you be willing me send me a sample part? DM me.

So I wonder what is the case use for such properties. Because if I want flexible, there is rubber or TPU.

great info guys, thank you very much !! So nylon will be somewhat flexible compared to ABS which will make it tougher?

Thank you, looks great now.

Well with this angle, you can't even see the first layer. Oh well. At least you have helped me confirm that this is normal.

I am sure this has been covered, but unless I am missing the idea here, this camera angle doesn't provide much info does it? I am wanting to adapt an external camera.

I am watching m printer set the first layer and I am noticing the artifacts below. this is UM PLA. Any ideas what could be causing this? I am using the OTTB settings for UM PLA.