Jump to content

Change Z Offset / Print in the air


Erkan3D

Recommended Posts

Posted · Change Z Offset / Print in the air

I want to print in the air without calibrating. Kind of a Z offset is needed.

 

I tried changing the height of the object (unmarked the auto drop option) but it prints on the surface or it needs support.

  • Link to post
    Share on other sites

    Posted · Change Z Offset / Print in the air

    Well I am not sure if I fully understand what you want to do but on the build plate select the model and then select the first icon from the vertical list of icons on the left hand side of the window. There you will see the x/y/z/ positions; the z will almost certainly be 0 and if you set it to a +ve number that will raise the model off the bed.

  • Link to post
    Share on other sites

    Posted · Change Z Offset / Print in the air

    So basically you want to print spaghetti, is that correct? I am a bit curious what the purpose is?

     

    Another method to achieve this might be to raise the design in your CAD editor to the required height. And then at a heigth of 0 add a little square, e.g. 10mm x 10mm, out of the way. So that square will sit on the glass, and the real design will be in the air. And switch off supports.

     

  • Link to post
    Share on other sites

    Posted · Change Z Offset / Print in the air
    24 minutes ago, geert_2 said:

    So basically you want to print spaghetti, is that correct? I am a bit curious what the purpose is?

     

    Another method to achieve this might be to raise the design in your CAD editor to the required height. And then at a heigth of 0 add a little square, e.g. 10mm x 10mm, out of the way. So that square will sit on the glass, and the real design will be in the air. And switch off supports.

     

    I was thinking about the second option but it would be great to print without adding extra stuff. I tried changing gantry height but didn't work. 

     

    For the purpose... 

    Let's say I am trying to make PLA drops. 

  • Link to post
    Share on other sites

    Posted · Change Z Offset / Print in the air

    Change your layer height to something absurdly high. I just did this with some vasemode prints I am experimenting with and it gave a sugared gumdrop look to the print. You still have to calibrate your z so that it has a basis for measurement to start from.

  • Link to post
    Share on other sites

    Posted · Change Z Offset / Print in the air

    @Erkan3D there are many ways to do this.

     

    One way is in cura settings to uncheck the feature that forces Z=0 and then click on the part in cura and make sure you have "move" selected in the upper left choices and then change the Z height to a value larger than 0.

  • Link to post
    Share on other sites

    Posted · Change Z Offset / Print in the air
    2 hours ago, gr5 said:

    @Erkan3D there are many ways to do this.

     

    One way is in cura settings to uncheck the feature that forces Z=0 and then click on the part in cura and make sure you have "move" selected in the upper left choices and then change the Z height to a value larger than 0.

    I did that and it didn't work. It needs a support otherwise it doesn't print. 

     

     

  • Link to post
    Share on other sites

    Posted · Change Z Offset / Print in the air
    3 hours ago, kmanstudios said:

    Change your layer height to something absurdly high. I just did this with some vasemode prints I am experimenting with and it gave a sugared gumdrop look to the print. You still have to calibrate your z so that it has a basis for measurement to start from.

    Tried that and it extruded absurdly high :)

  • Link to post
    Share on other sites

    Posted · Change Z Offset / Print in the air
    2 minutes ago, Erkan3D said:

    Tried that and it extruded absurdly high :)

    and absurdly in error? ;)

  • Link to post
    Share on other sites

    Posted · Change Z Offset / Print in the air
    5 minutes ago, kmanstudios said:

    and absurdly in error? ;)

    It extruded very high amount of filament since the volume get bigger 

  • Link to post
    Share on other sites

    Posted · Change Z Offset / Print in the air
    8 minutes ago, Erkan3D said:

    It extruded very high amount of filament since the volume get bigger 

    Anything like you wanted?

  • Link to post
    Share on other sites

    Posted · Change Z Offset / Print in the air
    35 minutes ago, kmanstudios said:

    Anything like you wanted?

    Nope. I want to extrude the same amount. 

  • Link to post
    Share on other sites

    Posted · Change Z Offset / Print in the air

    place a cube or something on the build plate somewhere and scale it very small, too small to print, like 0,1 x 0,1 mm. 

    • Like 1
    Link to post
    Share on other sites

    Posted · Change Z Offset / Print in the air

    image.thumb.png.3b02d9c53a6f57b37f089262f4cac670.pngHere  I attached an image. In solid view it is in the air but when it is time to print, it ignores the Z offset and prints on the bed.

  • Link to post
    Share on other sites

    Posted · Change Z Offset / Print in the air
    1 minute ago, peggyb said:

    place a cube or something on the build plate somewhere and scale it very small, too small to print, like 0,1 x 0,1 mm. 

    That worked! 

    I wish there was a setting to print in the air but I can use for now... THANKS!

    • Like 1
    Link to post
    Share on other sites

    Posted · Change Z Offset / Print in the air

    Very old post but maybe someone will still find it useful...

     

    There's a setting "Remove Empty First Layers".

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • UltiMaker Cura 5.8 Stable released 🎉
        In the Cura 5.8 stable release, everyone can now tune their Z seams to look better than ever. Method series users get access to new material profiles, and the base Method model now has a printer profile, meaning the whole Method series is now supported in Cura!
        • 5 replies
      • Introducing the UltiMaker Factor 4
        We are happy to announce the next evolution in the UltiMaker 3D printer lineup: the UltiMaker Factor 4 industrial-grade 3D printer, designed to take manufacturing to new levels of efficiency and reliability. Factor 4 is an end-to-end 3D printing solution for light industrial applications
          • Thanks
          • Like
        • 3 replies
    ×
    ×
    • Create New...