ultiarjan
-
Posts
3,778 -
Joined
-
Last visited
-
Days Won
76
Content Type
Forums
Events
3D Prints
Posts posted by ultiarjan
-
-
shortened screwdriver for removing the fancap, bent paperclip to hang the fancap on a rod, while changing the nozzle.
-
after changing my nozzle/heater many times on the UM2 there's no copper grease in there anymore, I assume it's probably a good idea to put some there... can I just use any type? any suggestions on the brand or type (I'm in the Netherlands)...
google;
-
just logged my first issue on github
there's a first time for everything .... -
@robert. Sure you can use my pictures.
I still think the main parameters are a dirty nozzle and softer fillaments. I should have tried the nozzle after i cleaned it with a burner... but cant anymore as i drilled it to 0.6mm.
Ill report when i see it again. But have not seen it in the last weeks.
-
@pm_dude i dont know how to log it .. i assume you mean on github?
-
enjoy !!
-
did anybody try colorfabb XT on an E3D ?
As this material needs a higher print temperature a full metal heater would be ideal...
-
Wat houd je tegen ??
Mijn programeer skills zijn nogal beperkt, kom niet veel verder dan office VBA en een beetje klooien met Arduino ... maar ga toch maar eens kijken... zal er vast iets van op steken.
-
our dog is the only one in the family with a FB acount :-P I just made him vote for you.
-
Harold, nice test!
Am I summarizing correct when I say the optimum for strenght is around 250 celcius ?
At what speed did you print the test units ? (higher speed needs higher temp ...)
-
-
think 14.09 is not an RC, and it's on the main cura downloadpage of the UM site ..
just installed 14.09.1RC2 and also here the strange move to the inside http://umforum.ultimaker.com/index.php?/topic/7488-trick-cura-to-change-print-path/?p=70060%20)%20on%20a%200%25%20infill%20part%20is%20still%20there.
on a 0% infill part is still there.
-
just checked the UM download page, there it is... so I just installed 14.09 and checked the same model again, the unneccesary move to the inside is still there ....
when I clicked "check for update" in cura 14.07 It told me I had thre latest version...
-
just tried to update to 14.09 but cura tells me 14.07 is the latest version .... seems they took down 14.09 .... so I can't test the same model in 14.09.
-
It may be more then just Z-scar, looks like what I had here;
http://umforum.ultimaker.com/index.php?/topic/7488-trick-cura-to-change-print-path/?p=70060
Anyhow, I like CURA a lot, even though it may not be 100% perfect ... but what software is?
-
I would advice not to use the standard feeder for this. When you pull the fillament out a long strand of plastics will often stay behind in your bowden, or worse you end up with bits of plastic in your feeder.
It's (IMHO) way better to use a feeder you can open and clean ... here's some links ....
https://www.youmagine.com/designs/alternative-um2-feeder-version-two
https://www.youmagine.com/designs/and-another-um2-feeder-design
-
https://www.youmagine.com/designs/ultimaker-2-fan-mount-dual--2
Its the v6.rev1.
I used xt. But others on this forum used pla apparently without problems...
-
I think you could have worse addictions
-
no worries, I'm glad you share your testing..... I'll be waiting patiently :-P
anyhow I'm still in doubt between your idea (probably the easiest) and a full metal E3D (better at high temperatures).
still trying to figure out if anybody has experience with Colorfabb XT and a full metal E3D.... I'll post the question in a XT thread...
-
I think it's nice to try to minimize the need for additional parts, but it seems like a good idea to just adapt this fan bracket to your needs.
https://www.youmagine.com/designs/ultimaker-2-fan-mount-dual--2#!design-information
just lower it 4.4 mm and make the hole for the nozzle a bit larger, as long as you'r using a single nozzle its a good idea anyhow (IMHO)...
Any change you'll share the complete drawing, including the way you changed the setscrew so I can find a machineshop to make one for me?
-
can you change the settings on the pictures (public?) I can't open large versions.
-
net over een lengte van 1 meter gechecked helemaal ok, zo +/- 2.82 en ook goed rond.
-
Best solution is to avoid overhang by changing the orientation you print the object in. Rotate in cad or in cura.
Think this is a good option in your case. Otherwise you need to use support... but this will always be a less nice surface...
-
Yes. I think it does. Did a before and after ultibot... with this fan setup the right ear was clearly better... this thing is more symmetrical.
And its more silent. Had some vibration noise on the metal one.. could not realy get some screws fixed properly... but ill save it ofcourse incase we someday get a dual nozzle setup
there's a first time for everything ....
5 axismaker
in Coffee corner
Posted
ha.. thats cheap, for just a 1000 pound you get the custom gcode for one model ......