3D Prints
1,105 files
-
Female Shepard 3D printing model from Mass Effect
By Gambody_3D
This model was tested in Cura 15.06. To avoid printing problems, we recommend the following settings:
Quality
Layer height: 0.1mm*
Initial layer thickness: 0.3mm
Bottom/top pattern: lines
Skin perimeter line count: 0
Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers).
*Layer Height 0.1mm is recommended for a better quality for the printed model. However, the printing time will double.
Speed setups:
Infill speed: 50mm/s
Outer shell speed : 30mm/s
Inner shell speed: 20mm/s
Top/bottom speed: 20mm/s
Support speed: 50mm/s
Travel speed: 150mm/s
Skirt speed: 30mm/s
Amount of slower layers: 4
Infill:
Infill pattern: Grid
Line distance: 3mm
Infill overlap: 20%
Infill layers: 0
Support:
Enable support: Check
Placement: Everywhere
Overhang angle: 30°
X/Y distance: 0.7mm
Top distance: 0.2mm
Bottom distance: 0.2mm
Stair step height: 0.5mm
Join distance: 0.7mm
Area smoothing: 0.6mm
Use towers: check
Pattern: Grid
Line distance: 1.5mm
Platform adhesion:
Type: Brim
Brim line count: 10 (up to 20, depending on the model’s height)
Other 3D printing recommendations:
Outer Shell Speed - 20mm/s and Support Speed - 40mm/s settings apply to avoid model deformation. Apply other settings by default.
Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.
8,303 downloads
(0 reviews)0 comments
Updated
-
Lifestealer N'AIX 3D Print Model | Static Figure
By Gambody_3D
For a smoother and more quality printing, apply the following settings in CURA printing software:
Quality
Layer height: 0.1mm
Initial layer thickness: 0.3mm
Bottom/top pattern: lines
Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers).
Speed setups:
Infill speed: 50mm/s
Outer shell speed: 30mm/s
Inner shell speed; 20mm/s
Top/bottom speed: 20mm/s
Support speed: 50mm/s
Travel speed: 100mm/s
Skirt speed: 30mm/s
Amount of slower layers: 4
Infill:
Infill pattern: Grid
Line distance: 3mm
Infill overlap: 20%
Infill layers: 0
Support:
Enable support: Check
Placement: Everywhere
Overhang angle: 30
X/Y distance: 0.7mm
Top distance: 0.2mm
Bottom distance: 0.2mm
Stair step height: 0.5mm
Join distance: 0.7mm
Area smoothing: 0.6mm
Use towers: Check
Pattern: Lines
Line distance: 1.0mm
Platform adhesion:
Type: Brim
Brim line count: 10 (up to 20, depending on the models height)
Other 3D printing recommendations:
Outer Shell Speed - 20mm/s and Support Speed - 40mm/s setting apply to avoid model deformation. Other settings by default.
Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.
2,363 downloads
(0 reviews)0 comments
Updated
-
(0 reviews)0 comments
Updated
-
Chaos Space Marine 3D Printing Mask
By Gambody_3D
Quality:
Layer height: 0.1mm*
Initial layer thickness: 0.3mm
Bottom/top pattern: lines
Skin perimeter line count: 0
Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers).
*Layer Height 0.1mm is recommended for a better quality for the printed model. However, the printing time will double.
Speed setup:
Infill speed: 50mm/s
Outer shell speed : 30mm/s
Inner shell speed: 20mm/s
Top/bottom speed: 20mm/s
Support speed: 50mm/s
Travel speed: 150mm/s
Skirt speed: 30mm/s
Amount of slower layers: 4
Infill:
Infill pattern: Grid
Line distance: 3mm
Infill overlap: 20%
Infill layers: 0
Support:
Enable support: Check
Placement: Everywhere
Overhang angle: 30°
X/Y distance: 0.7mm
Top distance: 0.2mm
Bottom distance: 0.2mm
Stair step height: 0.5mm
Join distance: 0.7mm
Area smoothing: 0.6mm
Use towers: check
Pattern: Grid
Line distance: 1.5mm
Platform adhesion:
Type: Brim
Brim line count: 10 (up to 20, depending on the model’s height)
Other 3D printing recommendations:
Outer Shell Speed - 20mm/s and Support Speed - 40mm/s settings apply to avoid model deformation.
1,455 downloads
(0 reviews)0 comments
Updated
-
Robot 3D print
By designsoul
Finished with Chrome spray paint, this print looks wonderful.
864 downloads
(0 reviews)0 comments
Updated
-
Escher in Real Life
By fbrc8-erin
I was looking for something I could only print on a UM3 and I think I found it. I originally saw this file on Thingiverse and saw that no one had printed it, and hunted it back to it's source, here: http://www.cs.technion.ac.il/~gershon/EscherForReal/
I'm overall pretty impressed with how this came out. The totally flat overhangs came out beautiful with 100% interface on the PVA:
1,625 downloads
(0 reviews)0 comments
Updated
-
Atlas 3D Printing Recommendations
By Gambody_3D
Quality
Layer height: 0.1mm*
Initial layer thickness: 0.3mm
Bottom/top pattern: lines
Skin perimeter line count: 0
Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers).
*Layer Height 0.1mm is recommended for a better quality for the printed model. However, the printing time will double.
Speed setups:
Infill speed: 30mm/s
Outer shell speed : 30mm/s
Inner shell speed: 20mm/s
Top/bottom speed: 20mm/s
Support speed: 50mm/s
Travel speed: 150mm/s
Skirt speed: 30mm/s
Amount of slower layers: 4
Infill:
Infill pattern: Grid
Line distance: 1.5mm
Infill overlap: 20%
Infill layers: 0
Support:
Enable support: Check
Placement: Everywhere
Overhang angle: 30°
X/Y distance: 0.7mm
Top distance: 0.2mm
Bottom distance: 0.2mm
Stair step height: 0.5mm
Join distance: 0.7mm
Area smoothing: 0.6mm
Use towers: check
Pattern: Grid
Line distance: 1.5mm
Platform adhesion:
Type: Brim
Brim line count: 10 (up to 20, depending on the model’s height)
Other 3D printing recommendations:
Outer Shell Speed - 20mm/s and Support Speed - 40mm/s settings apply to avoid model deformation. Apply other settings by default.
1,016 downloads
(0 reviews)0 comments
Updated
-
Dragon
By zpm3atlantis
Die ist ein Beweglicher Drache, er besteht aus 42 Gedruckten Teilen. Sogar die Augen sind gedruckt.
Der Ersteller dieses Moddels ist wirklich ein Meister, ein grund warum ich es hier gepostet habe.
Hier nochmal ein link direkt zu ihm.
http://www.soniaverdu.es/
http://diwo.bq.com/dragon-braq/
Aber Vorsicht, dies ist ein sehr Anspruchsvoller 3d Druck.
http://msxanimations.deviantart.com/
1,182 downloads
(0 reviews)0 comments
Updated
-
Kitten in ColorFabb bGen
By LePaul
I was up for a challenge and found this highly detailed kitten model
I used Simply3D and 0.2 layers
ColorFabb nGen filament
821 downloads
(0 reviews)0 comments
Updated
-
Makerbot headphone stand
By asykesey
came out pretty well, i now have one at the office and one at home
815 downloads
(0 reviews)0 comments
Updated
-
HT Clear experiment
By IRobertI
Playing around with some Colorfabb HT. Quite happy with this one. Obviously it has been post processed by sanding and polishing (the side facing down in the picture is the side against the glass so that was untouched though).
5,581 downloads
(0 reviews)0 comments
Updated
-
Ultimaker nozzle box
By gizmo999
So i didnt like the cardbox version of my nozzle box so i made a new one ,and i like to share it with you .
1,668 downloads
(0 reviews)0 comments
Updated
-
Baby Groot
By LePaul
I got this model from a link the 3D Printing Nerd had provided (I think it has since moved around a bit) Per his video, I used Simplify 3D to address separated layers and then, it was easy! Generate the support structures and print each piece, body took 9 hours, head took 8 hours
Clean up was easy!
1,482 downloads
(0 reviews)0 comments
Updated
-
(0 reviews)0 comments
Updated
-
(0 reviews)0 comments
Updated
-
Baby Groot
By Gigi
50% reduced
Ultimaker Nylon transparent (default Cura 0.1mm profile)
Playing with markers
926 downloads
(0 reviews)0 comments
Updated
-
Baby Groot
By zizon
Baby Groot by Byambaa
Published on January 7, 2017
www.thingiverse.com/thing:2014307
Impression en Coconut, 80% de l'original.
Sans post traitement.
784 downloads
(0 reviews)0 comments
Updated
-
(0 reviews)0 comments
Updated
-
(0 reviews)0 comments
Updated
-
My work colleagues
By cloakfiend
Havenst posted here in a while, but just a bunch of rough quick prints of the team of people I work with, all made with remake or memento or whatever, shame they discontinued the mac version as it was free! lol no more, will have to find a new quick method now. Photoscan is a lot longer than rekmake. Then sprayed with various undercoat brands of paint for experimentation. will post a few close ups if I have them as I've given all these to their respective selfs.
1,069 downloads
(0 reviews)0 comments
Updated
-
(0 reviews)0 comments
Submitted
-
USS Voyager on UM3X
By fbrc8-erin
I printed this USS starship Voyager model at nearly maximum Z-height on a UM3X, with dissolvable supports. The picture doesn't show the scale well, but it's about as long as my forearm. I'll ad some close up shots soon; the level of detail in the model really impressed me.
833 downloads
(0 reviews)0 comments
Updated
-
(0 reviews)0 comments
Updated
-
(0 reviews)0 comments
Updated
-
Some kind of monster
By marco3D
I started fiddling with Blender, and ended up with this monster.
588 downloads
(0 reviews)0 comments
Submitted
