3D Prints
1,105 files
-
Impression PLA en 60 pièces différentes.
By Biddle
Impression PLA en 60 pièces différentes.
903 downloads
0 comments
Updated
-
First 3d Print
By MaciejGliwa
This my first 3d print done on Ultimaker 3, hope you guys like it.
728 downloads
0 comments
Updated
-
0 comments
Updated
-
Carbon Freeze fun
By cloakfiend
Just a fun quick over-extrusion mess around, i didn't spend long on this because i'm giving it to a mate(the guy in it) who is a starwars fan as a gift, and i dont think he'll care about the fingers, i may try it without over extrusion to see if the fingers come out better.
1,184 downloads
0 comments
Updated
-
Melt Face in Colorfabb Intense Green PLA
By RetromanIE
Melt Face in Colorfabb Intense Green PLA
1,439 downloads
0 comments
Updated
-
Screaming manq
By qmaker
I was working on another project and ended up with this as a side piece. Printed it and mounted it to the back of my Camper. Too funny, I am sure people must think I am a nutjob. This is what happens when you have an Ultimaker and you can make anything you want.
1,461 downloads
0 comments
Updated
-
Alien face (failed print)
By cloakfiend
This is an Alien face that printed kinda wrong for some weird reason, no acetone treatment yet, but i was really happy with the details especially the teeth. Should look great after a acetone bath!
2,048 downloads
0 comments
Updated
-
B.A.W. ( Base Anti-Warping ) Experimental
By rigs
Base : PETG / CF Nanovia
Warp test : TPC Flexifil Formfutura
Printed with MARK 2
608 downloads
0 comments
Updated
-
0 comments
Updated
-
0 comments
Updated
-
Ultimaker 2 Encasement
By Eraser
I built a plexiglass encasement for my Ultimaker 2. It includes an upper encasement with openable upper lid, a front openable door, and a rear HEPA filtration unit. The HEPA filtration unit has been designed for compatibility with readily available vacuum cleaner HEPA cartridges. An exhaust fan is mounted to the exterior surface of the rear plexiglass panel. The front door includes hinges, and a pair of door locks that you rotate to lock the front door closed.
Because my Ultimaker 2 is my baby, I designed the enclosure completely non-destructively. None of the components are fastened to the Ultimaker by screws or the like. Instead, the upper encasement is mounted by Mounting Clips that frictionally engage the upper frame of the Ultimaker, and the door is mounted by hinges that frictionally engage the front frame of the Ultimaker. All components are printed in Ultimaker Metallic Grey.
2,176 downloads
0 comments
Updated
-
0 comments
Submitted
-
Centrigugal Fans Duct using a bottom heat resistant air blow deflector
By gudo
Recycling your prefered beverage can for improving the printed fan duct life time with any material
The central portion of the fan duct below the heat block can now better heat resists
by using a beverage can thin and light metal sheet part (0.2mm thick)
It's can be easy cutted with a scissor and it's easy formed by a forming printed tools
PLA would be used now for printing the fan duct for those prefer this material
1,772 downloads
0 comments
Updated
-
0 comments
Updated
-
Kalimaaa
By cloakfiend
Got a few issues with my printer at the mo not sure what exactly. end of the roll old coupler or something else.....
no cleaning done at all, just acetoned, so bits of pla here and there from the lack of retraction even though it was turned on?
a fun job again.
724 downloads
0 comments
Updated
-
0 comments
Updated
-
Gopro mount on mtb fork
By ar3d
This is the first thing I printed, used to mount the gopro camera on the MTB fork with cable ties
1,398 downloads
0 comments
Updated
-
0 comments
Updated
-
3D Scanner
By designsoul
Functional low-cost photogrammetry 3D scanner, entirely built with the Ultimaker, the chassis split into four parts and finished with epoxy resin.
1,644 downloads
0 comments
Updated
-
Japanese pagoda
By lekid
3d modeling of a One Tier Pagoda for a Lantern project with ZBrush 4r7.
Painting :
- Primer : MrSurfacer 1000 (airbrush)
- Tamiya Black Semi Gloss (airbrush)
- Tamiya Copper (airbrush)
- Pébéo Studio Acrylics HV iridescent precious gold (hand painted)
- Varnish Tamiya Clear (airbrush)
653 downloads
0 comments
Updated
-
Alléluia
By duriel
Reproduction d'une console d'ornement pour un lieu de culte.
Numérisation: photogrammétrie
Poids ; 13.1 Kg
Temps d’impression 594 Heures
Nombre de pièces : 35
Post traitement : résine (Nanovia) + peinture à venir...
Dimensions :
Hauteur 156 cm
Largeur 73.04 cm
Profondeur 14,6 cm
Volume. 229.89 cm3
954 downloads
0 comments
Updated
-
0 comments
Submitted
-
Mark 2 (dual extruder mod for UM2) test after upgrading to 3DSolex block/nozzles
By conny_g
Mark 2 (dual extruder mod for UM2) test after upgrading to 3DSolex block/nozzles
643 downloads
0 comments
Updated
-
Redesign Housing Anders Olsson Nozzle Torque Wrench
By Tosch
I redesigned the housing for this nozzle torque wrench so that it also can be used as a nozzle holder. This nozzle holder has six threaded holes for the nozzles 0.25, 0.4, 0.6, 0.8, 1.0 and 1.2mm.
2,220 downloads
0 comments
Updated
-
Project FLOLA
By VitR
Make a design table lamp electronically controlled.
Change the shape of the lamp and light intensity according to your mood.
Ready for 3D print - microcontroller Arduino - stepper motor - Joystick control.
Full story on
http://www.3lobitprint.cz/en/flola.html
638 downloads
0 comments
Updated