3D Prints
1,105 files
-
(0 reviews)0 comments
Updated
-
Fork / Spoon Handle
By dbrgn
My wife occasionally has problems with her joints. When they hurt and are swollen, she can barely hold a fork or spoon in her hand.
There is "orthopedic" cuttlery with thicker handles that can be bought, but they're usually expensive and/or ugly. We wanted something that would benefit everyone by making a 3D-printable handle for widely used (and easily available) IKEA forks.
Goals:
modify / improve a fork so that it can be used by people with joint problems
it needs an "angled" surface, so that it's easier to grip
it should fit a regular IKEA Dragon fork and/or spoon
it should be removable, so that the forks can be washed in a regular dishwasher
it should be easy to print without support material
I designed the handle in OpenSCAD so that the parameters could be customized if someone wants a thicker handle or has a different fork. It fits both the fork and spoon in the IKEA Dragon cuttlery set. The source code can be found here, licensed as CC BY-SA so that others can profit too.
2,542 downloads
(0 reviews)0 comments
Updated
-
Cartoon Megatron
By cloakfiend
I think i overdid the distressing on this one and i need to fix his fish lips, lol.
1,346 downloads
(0 reviews)0 comments
Updated
-
Muséum
By duriel
Bouchon de réservoir scanner par "un conseil des musées" mais je ne connais pas la marque de cet ancien modèle de voiture.
(24 heures de polissage).
1,831 downloads
(0 reviews)0 comments
Updated
-
The Good "full body"
By al1-ch
Figurine The Good
Fan art de: The good, the Bad and the Ugly
impression en 3 parties:
1. La tête, le chapeau et le haut du poncho (imprimé couché, ça bouffe un peu l'arrière mais ça ne gêne pas trop je trouve, dommage collatéral à cause du cigare)
2. Le corps (impression debout)
3. Le socle (pas obligatoire car le perso tient debout tout seul)
Taille: les fichiers STL à 80% = figurine de 16,5 cm de hauteur C'est la taille des figurines sur les photos
1,997 downloads
(0 reviews)0 comments
Updated
-
umo(+) delux mounting assembly for RaspPi camera
By peetersm
Mount a Raspberry Pi camera+wide angle lens+ LED lights inside your printer.
I made this design to solve/address the following:
1. Clean looking mount for RasPi camera and lights inside frame.
2. Increase viewing angle of camera.
3. Light the print bed for camera.
I like Octoprint for viewing my prints AND taking time-lapse movies of print jobs. I did not want a camera hanging off outside of the printer, I wanted it to be inside the frame if possible. I also wanted to have light since sometimes the room is dark. I wanted as little hacking to the printer as possible (just a few drill holes in the frame).
SO this is what I made. When the camera is inside the frame it needs the help of a wide angle lens to see the whole print bed. I also decided to power the LEDs from the Pi to reduce the power supplies I would need. There are a bunch of photos to show my process. I will try to add better instructions later.
1,878 downloads
(0 reviews)0 comments
Updated
-
WedgeBot for Ultimaker2+
By ultiarjan
Is it a bird? is it a plane? NO it's WedgeBot.
Getting tired fingers? let this little guy stick his wedge into your feeder!
this thing is a redesign of;
https://www.youmagine.com/designs/the-wedge
and the famous Ultibot.
1,932 downloads
(0 reviews)0 comments
Updated
-
Giulietta (basic)
By neone
I let your imagination run wild towards the function of this one.
18+ orientated.
resize to your own pleasure.
1,482 downloads
(0 reviews)0 comments
Updated
-
(0 reviews)0 comments
Updated
-
Crossflow Cooling for UM2
By avogra
This is a first try to bring the laminar crossflow cooling invented by @foehnsturm to the Ultimaker 2 without having to lay hands on your beloved shiny printer ;)It is attached with Tesa Powerstrips. Intention is, that air circulates through the fans and the long nozzle, across the printing layer, down left of the build-plate and back into the fans. The radial fans (Titan TTC-003) are quite cheap (<10€ each). I didn't want to waste filament and printing time on the large flat surfaces so instead I included some 0.8mm acrylic glas I had around.
When I'm satisfied this hopefully gives all the UM2 owners a cheap and simple way of a crossflow cooling.
It has still some shortcomings:
airflow is a bit weak
some air goes through the top and the front instead of around the buildplate
airflow widens and decreases from right to left
Right now it improves overhangs when combined with the stock fans but is too weak as the only cooling. Unfortunately the nozzle has to be that thin to prevent collision with the fan shroud.
Ideas for improvement are
a recessed cover for the front so the air is forced around the buildplate
an airguide on the left side, so that also with the buildplate lowered, the air is sucked in at the height of the current printing layer, maybe even equipped with another set of fans
a wider airnozzle to increase airflow and removing the stock fans and fan shroud
2,068 downloads
(0 reviews)0 comments
Updated
-
Moai Fridge Handle
By Nicolinux
I had an awful kitchen at first and until the new one was ready, I had to do something about the broken fridge handle
2,014 downloads
(0 reviews)0 comments
Updated
-
WIP - The Good
By al1-ch
Premier test d'impression de la tete de Clint, (5 cm) .... le corps est en cours de modélisation
1,361 downloads
(0 reviews)0 comments
Updated
-
Ultimaker Original Plus - Penstock
By aerobubulle
This penstock can be used with a computer fan to guide the air away from the bottom of the UMO+ and cool the electronics. The square opening should directed towards the back of the printer and placed next to the back left foot. ! Be careful, you'll need to raise the UMO+ by approximately 4 centimeters. ! ~ Designed for a special case. ~
I cut the design into 2 parts to avoid having supports I can't remove in the tube. There are still some left, but I find them easier to remove.
1,338 downloads
(0 reviews)0 comments
Updated
-
EDTracker Case
By Nicolinux
This is a case for the great (and free) EDTracker head tracking thingy. This is for the protoboard version:
https://edtracker.org.uk/index.php/diy/build-it/protoboard
1,869 downloads
(0 reviews)0 comments
Updated
-
Bowden tube clamp for the UM2 extruder feeder
By umagi
I made this to prevent the bowden tube from popping out of the feeder. For some reason on my self-built printer, this usually happens during the print of the first layer (starting with the brim).
Since the tube is pushed out with quite some force, I resorted to this design, which combines the function of the shoehorse clip (to lift the ring fitting) and of a 25mm clamp, which squeezes the bowden tube to hold it firmly in place.
The design is for a 4mm external diameter bowden tube (1.75mm diameter filament).
1,278 downloads
(0 reviews)0 comments
Updated
-
(0 reviews)0 comments
Updated
-
Random Shroud
This is a random part for a machine at work.
We were very impressed how it turned out since it has thin walls and big overhangs.
I used the FAST settings in S3D with a few modifications.
The filament is 3D Universe PLA.
1,494 downloads
(0 reviews)0 comments
Updated
-
The Ultibot/olsoon block Contest
By darkdvd
5.65 mm and 5.95 mm for me !
Printed with an Ultimaker 2 / Olsson block @ 0.4 (Jet Nozzle)
1,744 downloads
(0 reviews)0 comments
Updated
-
(0 reviews)0 comments
Submitted
-
Usb holder (first print)
By pootis_owner
This is my first self designed printed pice
1,298 downloads
(0 reviews)0 comments
Updated
-
(0 reviews)0 comments
Updated
-
(0 reviews)0 comments
Updated
-
Cute Desert Eagle
By cloakfiend
just a little test trying to get to grips printing and glueing split objects. i still have some issues, i need to sort out. i find small single objects hard to print at times.
1,682 downloads
(0 reviews)0 comments
Updated
-
Rugby Ball Gift
By lekid
3d printing done for the daughter of a Rugbyman friend.
Done in 4 parts with Colorfabb ngen and FormFutura HDGlass.
Now, I know that I have to improve my paint skills with the airbrush
1,223 downloads
(0 reviews)0 comments
Updated
-
Steampunk Photo Frame
By psine
Un cadre photo (10*15cm) par Don Foley imprimé en PLA et peint à l'acrylique.
1,410 downloads
(0 reviews)0 comments
Updated
