43 minutes ago, kmanstudios said:I still want the dilithium crystal matrix for off grid power operations
With an integrated Scotty AI?
43 minutes ago, kmanstudios said:I still want the dilithium crystal matrix for off grid power operations
With an integrated Scotty AI?
3 hours ago, Marco_TvM said:With an integrated Scotty AI?
Absolutely!!
I have forget , somehow a little bit longer axle so the print head could use all the build plate ,
no matter if one AA core , or core AA + BB is used . (blind zones in Cura preview).
I wonder if it would be possible to use a revolving print head to fit multible print cores. It would be more complex but could take up less space than the current side-by-side setup.
3 hours ago, Coalwater said:I wonder if it would be possible to use a revolving print head to fit multible print cores. It would be more complex but could take up less space than the current side-by-side setup.
Then we could call it the "Colt Aught point 4'.
Yes, I am American....I grew up around guns and was in the Navy......
Woops...thanks to @Labern pointing out that this did not belone here, it is removed...sigh....I do not know what happened.....mutter, mutter......
Edited by kmanstudios@kmanstudios was your last post supposed to be here?
2 hours ago, Labern said:@kmanstudios was your last post supposed to be here?
I see the post above your post....am I missing something?
Your post seems to be about a CURA issue rather then what you want in a UM4
ack!!!!!
Thank you!!
13 hours ago, Coalwater said:I wonder if it would be possible to use a revolving print head to fit multible print cores. It would be more complex but could take up less space than the current side-by-side setup.
That might become pretty messy with the Bowden tubes.
15 hours ago, kmanstudios said:Then we could call it the "Colt Aught point 4'.
Yes, I am American....I grew up around guns and was in the Navy......
Hehehe, good one! I had the word "Revolver" in mind while I was writing this.
6 hours ago, Dim3nsioneer said:That might become pretty messy with the Bowden tubes.
Yeah, that would be a challenge, but I got a few ideas.
Have a 2+ that I'm generally happy with; in the market for a second printer, but I will be very pissed off if I put down big bucks on a 3 and then the Ultimaker 4 comes out two months later. One thought is to buy one of the impressive low end machines, so I have a back up and can use for simpler tasks. Still can't fins any hints on when the Ultimaker 4 will come out.
RGB all the things
6 hours ago, FaultyTowels said:RGB all the things
??????
4 hours ago, kmanstudios said:??????
lol. I think he means everything should be color control. Lots of pretty lights. The 2 cores and the primary lights aren't enough for this guy.
11 minutes ago, gr5 said:lol. I think he means everything should be color control. Lots of pretty lights. The 2 cores and the primary lights aren't enough for this guy.
Oh...ok...I too like the twinklies, but not in my interfaces.....
On 01/04/2018 at 10:47 PM, kmanstudios said:Oh...ok...I too like the twinklies, but not in my interfaces.....
He could mean 3 feeders, one red, one green and one blue, all mixing in the nozzle to make every color possible. But beyond the mess and the technological limits, I think everything would just come out brown...
Also, after spending 2 hours cleaning our printer, please remove the dead space below the printbed where only scrap plastic goes and you can't reach to clean! And as said before, please, ultimaker, please, close this da** printer!!!!!!!!! Why was it so difficult to put a door and a fan controlling inside temp?!? Also a better UI would have been good....
49 minutes ago, Swissengineer said:Why was it so difficult to put a door and a fan controlling inside temp?!?
Because every single profile would need to be changed and re-tested.
Recommended Posts
Top Posters In This Topic
22
8
8
7
Popular Days
Nov 14
12
Jan 31
9
Mar 28
8
Nov 17
8
Top Posters In This Topic
kmanstudios 22 posts
SandervG 8 posts
Swissengineer 8 posts
Labern 7 posts
Popular Days
Nov 14 2017
12 posts
Jan 31 2018
9 posts
Mar 28 2018
8 posts
Nov 17 2017
8 posts
Popular Posts
Swissengineer
Are you sure your problems are with the printer? or the interface between the chair and computer....
kmanstudios
Dear UltiSanta, I have been a good boy this year and would like to see the following things on an Ultimaker 4 system: Larger build volume because, well, I like big things and I cannot lie,
Labern
Option of a bigger build volume. New silent step control board with more smarts. Closed-loop stepper-motor control with step-loss compensation. Light weight direct drive. 5 extruders, system l
Posted Images
Xalara 6
My wishlist:
Don't get me wrong, I love my UM3, but there's lots of room to improve
Edited by XalaraLink to post
Share on other sites
kmanstudios 1,120
I still want the dilithium crystal matrix for off grid power operations
Link to post
Share on other sites