Jump to content

carmamir

Dormant
 View Profile  See their activity

  • Posts

    48

  • Joined

  • Last visited

 Content Type 

Topics posted by carmamir

  1.  

    Weird issues with certain model on Cura 4.13.1 (blobs/zits on corners/ only one wall)

    By carmamir, in UltiMaker Cura

      
    • 1 reply
    • 251 views
  2.  

    EPCOS 100K Thermistor and wrong temperature showing (155)

    By carmamir, in UltiMaker 3D printers

    • 1 reply
    • 2,184 views
  3.  

    Bultimaker is destroying Arduino on Ultimaker ??? Second motherboard damaged by firmware from this site

    By carmamir, in UltiMaker 3D printers

    • 13 replies
    • 2,559 views
  4.  

    UMO - Merlin built with 250000 baud rate. Now cannot upload any other firmware Cure/Arduino

    By carmamir, in UltiMaker 3D printers

    • 0 replies
    • 1,098 views
  5.  

    Can I clean ABS/PLA in Acetone/NaOH in ultrasonic cleaner ?

    By carmamir, in Improve your 3D prints

    • 1 reply
    • 2,485 views
  6.  

    UM + E3D + Enclosed + Heated bed + UniController - UK

    By carmamir, in Buying or selling your UltiMaker

    • 8 replies
    • 2,049 views
  7.  

    E3D causing jams after 1-3 hours of printing. PLA

    By carmamir, in Third party products & modifications

    • 6 replies
    • 5,053 views
  8.  

    Insufficient infill between layers

    By carmamir, in UltiMaker 3D printers

    • 4 replies
    • 2,036 views
  9.  

    Teflon tube is sliding off from teflon insulator...

    By carmamir, in UltiMaker 3D printers

    • 1 reply
    • 1,231 views
  10.  

    Cura settings for Prusa i3

    By carmamir, in UltiMaker Cura

    • 3 replies
    • 84,579 views
  11.  

    After week of break, X and Y axis LOCKED, can't move by hand (on/off)

    By carmamir, in UltiMaker 3D printers

    • 4 replies
    • 1,379 views
  12.  

    Ultimaker v3, best extruder replacement ?

    By carmamir, in Third party products & modifications

    • 15 replies
    • 4,116 views
  13.  

    What to adjust so Ultimaker can start printing wholes for M3/M4 (now holes are too small)

    By carmamir, in UltiMaker 3D printers

    • 8 replies
    • 4,515 views
  14.  

    Bottom layer... Set to 15mm/s but in real it's printing like 70 or 80mm/s

    By carmamir, in UltiMaker Cura

    • 1 reply
    • 982 views
  15.  

    Can't calibrate steps per mm... 24.78-25.08mm on 25mm test print

    By carmamir, in UltiMaker 3D printers

    • 1 reply
    • 1,434 views
  16.  

    Ultimaker filament glueing to hotend. Fail to print every time after big failure of cold bed

    By carmamir, in UltiMaker 3D printers

    • 13 replies
    • 8,379 views
  17.  

    Extruder stopped working. Do I need new motor or electronics ???

    By carmamir, in UltiMaker 3D printers

    • 4 replies
    • 3,252 views
  18.  

    Weird problem with printing of fan holder... Prints below existing layers... (hot end is printing IN plastic)

    By carmamir, in UltiMaker 3D printers

    • 6 replies
    • 1,251 views
×
×
  • Create New...