RogueWave

Thanks very much for the detail info File enclosed cura.log

Please explain Log File..how to get it etc..

Cura had no problem loading Blender files but today, loading a file which loaded fine days ago, the loading bar appears loading but nothing loaded even after a 5 minutes or displays file corrupt etc...Rebooted win 10 pro, have SSD drive really stuck.....uninstalled cura then installed no change ..... Really, can't figure it out!!!!!

Must say my network is strange from time to time 1) Cura 4.9.1 2) 4.12.0 3) 4.12.1 uninstalled 4.12.0 but listed in photo what is Cura 4.9.1?? need advice on above thanks

abled UM3 only and back to slow to dead slow with Cura on just selecting a model, then trying to move it.....

Disabled those plugins and speed is GREAT......thanks but lost cloud printing on my S5......cuz UM3 disabled now??????? Correct?????

Have to wait 5 to 6 seconds or more to select a model, move it, select material etc....task manager indicates 2% CPU or more with very high to moderate POWER USAGE have to close Cura and reload then it's fine for awhile maybe back to slow again Suggestions?????? Thanks

My dope sheets states dry it for at least 12 hours before use.... not a oven drying, buy one $150 or so

I have SSD drive 48 core and Cura is slow slow slow on S5

What brand filament are you using?????? settings for: Plate temp Filament

Switching the nozzle from 2 to 1 and 1 to 2 solved the problem.....it's deep in the support pages online......wish that appeared instead of a short brief on what to do.....acces to complete data is a problem.......

Number 2 is a device to install a nozzle into to unclogg a nozzle. seperate from my S5.... works off 110v etc just a small device to heat up the nozzle for hot/cold pull operation

Working fine for months then bed leveling issues did all the info online i.e. clean bed, clean nozzles, reset printer...even new glass plate then it worked few times back to manual leveling done .......... but when new job is started, leveling failed any suggestions?? thanks latest Cura and firmware installed

1) On the cover for the filament feeder, like to see a clean plastic cover, to see if the gear is clogged up with filament particales. Taking the cover off and on is not necessary with a clear cover. 2) Cleaning the nozzle consumer a lot of down time. Having a seperate device, for cleaning, while my S5 is printing is a must have item....saves a lot of time 3) Printer stop half way during a 2 day print job, filament not feeding maybe empty spool......problem was a clogged nozzle.....forced to abort job.... have the option to clean/change a nozzle, then rusume printing..... Please consider the about to supplement an already excellent printer to make it a super super printer!!!!!!!! Thank you

Those fuzzy lines on the bow are the same results from time to time not often on my S5 with air manager one print layer can be slight off cause the issue then back to a fine print.......I think the filament is the issue.....

Excellent advice...forget apply adhesive to the corner!

The Blob prints fine but after finishing the print head remain just above the blob, then starts the brim sequence, which drags the blob across the build plate or sticks to the nozzle. At time, destroys the print.....Just raise the print head 5mm more after the blob operation is finished. Thanks

Running test on Fuzzy features IT'S NOT FUZZY ENOUGHT! HA HA Any thoughts? Concern about yellow warning... Important? Thanks

Check the condition of the nozzle cover, nozzle exterior might have some material on it .........looks like problem I had

Trying to replace worn cover newly purchased one not as robust as original.....new tear easy where can order good ones, some are in backorder status Boston,Mass US? Thanks

Printed excellent Ultimaker TPU 95A, but tried to unload filament just moved about 5 mm and stopped hearing the gear still working until normal end cycle. Tried relief the tension on the filament by flipping the level and pulling the filament but no go ....it stretches repeated the above two methods several times but no go what's the best next step? Thanks

It's better but has this test Blender set to MM units.... 200MM cube created Cura says too small scaling up size is 5MM scaled up to 2500% Blender same saved cube in OBJ Cura: object too small scaling up size 0.2 scaled up to 100% Before change to MM Cura file corrupt etc. or scale up Changed to MM Cura recognized the object but size is not accurate Uninstalled Blender plug-in from Cura No change on before and after Some progress is better than none

in Blender save model to export to OBJ format and Cura reads the file and increases the size 5 to 6 times in xyz save same model in Blender format, Cura reads it too small increasing size or file is empty, corrupt etc. What to do next???? Thanks cura 4.10 blender 2.93

My supplier gave me a refund on the Jabil SEBS 1300 95A filament too many odd problems........very glad have a excellent S5 machine which narrows down the problem to others Hats Off to development team

Air Manager on order no material station Went into configuration folder and uninstall Jabil 1300 95A Quick Cura started Cura message install Jabil and sync settings, extruder one, and material shows Jabil and others third party materials for the first time set up model select Jabil had to over ride warning after 10 minutes of printing it stopped indicating empty spool in fact spool full with no tangles whatsoever material easy to pull out by hand Resume printing Brim printed well and firm to glass plate but first layer strings with ok adhesion but not smooth Final surface print very good first two photos Second print the same model moved to different location on build plate printer stop again warning empty spool in fact like about third photo shows when printing stop first layer spots pattern no solid lines …..setting in Cura Cubic using my infrared thermometer, old one, bed temperature of 65C material calls for 70C Real odd Brim is excellent but first layer is terrible.