Jump to content

Improve your 3D prints

Help, tips & tricks

5,369 topics in this forum

  1. How to engrave less outlines on bottom and top layers

    By lovethepirk,
    • 1 reply
    • 291 views

  2. Method for easy supports detachment

    By func_myxomop,
    • 0 replies
    • 298 views

  3. Noob Benchy help

    By 3DMaughan,
    • 0 replies
    • 321 views

  4. Sudden underextrusion during print

    By orlin278,   
    • 9 replies
    • 1.8k views

  5. Adhesion Problems... I think?

    By 0v3rrat3,
    • 1 reply
    • 308 views

  6. .

    By Genox,
    • 0 replies
    • 568 views

  7. Blobs occuring. Coasting and Z Seam Adjustment does nothing.

    By Turbo,   
    • 2 replies
    • 1.7k views

  8. Cura 5.0 issue - "Wall Ordering" not changing for single line inner wall

    By kiwistylebuild,   
    • 4 replies
    • 1.6k views

  9. How to Update the Screen Files on a DACAI Screen (Ender 3 V2)

    By Schmordan,
    • 2 replies
    • 1.1k views

  10. Overwritten the PRIVATE file On Ender 3 V2 Display

    By Schmordan,
    • 2 replies
    • 764 views

  11. Joined up writing

    By WindyMiller,
    • 3 replies
    • 417 views

  12. Request for a new setting - Z-hop only on first layer

    By stejan,   
    • 2 replies
    • 701 views

  13. imporve the pinting qulity of the breakaway material

    By Curtismech,
    • 0 replies
    • 263 views

  14. Can the difference in print dimensions in the X,Y plane when using fine Low Quality to Super Quality be accommodated in the software.

    By TimBL,
    • 2 replies
    • 411 views

  15. Need help identifying and naming the issue with print

    By kkurzynowski,
    • 0 replies
    • 270 views

  16. UM3 Extrudes during Active Leveling

    By donbon,   
    • 1 reply
    • 329 views

  17. How to make continuous printing on thin bottom surface for embedded magnet?

    By DavidTruong,   
    • 0 replies
    • 289 views

  18. Could something about a model cause the printer to jam?

    By jetfire158,
    • 0 replies
    • 306 views

  19. How to improve layer adhesion after Pause at Layer/Height script

    By jetfire158,   
    • 10 replies
    • 1.8k views

  20. Is there a way to disable active leveling for ultimaker 3 extended?

    By sycamore361,
    • 0 replies
    • 345 views

  21. How do you actually load parts in the position they were saved?

    By FraggleRock,
    • 2 replies
    • 528 views

  22. The bed is too close and too far away

    By tienntrann101,
    • 1 reply
    • 345 views

  23. Problem With Support

    By minuteman64,
    • 2 replies
    • 355 views

  24. Confirmation of Retraction Setting overwrite and Dual Print Head settings?

    By Krinthos,
    • 1 reply
    • 186 views

  25. Outer layer peeling off

    By TCP,
    • 0 replies
    • 513 views

  • Our picks

    • UltiMaker Cura 5.7 stable released

      UltiMaker Cura 5.7 stable released

      ArunC posted a topic in UltiMaker Cura,

      Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
       
      • 18 replies
      MariMakes

      Picked By

      MariMakes,

    • Release Notes: S-Line Firmware 8.3.0 (Latest)

      Dustin posted a topic in Firmware,

      S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
      (Sorry, was out of office when this released)

      This update is for...
      All UltiMaker S series  
      New features
       
      Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
      • 0 replies
      MariMakes

      Picked By

      MariMakes,
    View All
×
×
  • Create New...