Jump to content

UltiMaker 3D printers

Our line of reliable 3D printers 

8,837 topics in this forum

  1. What software/firmware and settings would you use?

    By yourexpressions,
    • 1 reply
    • 1.2k views

  2. Steppers in slave mode

    By snowygrouch,
    • 7 replies
    • 2.2k views

  3. I can extrude PLA but can't extrude ABS at all????

    By kinginnovator,
    • 12 replies
    • 6k views

  4. UM Config suggestions

    By bob,
    • 4 replies
    • 1.7k views

  5. The Plug is back - V2 HotEnd :-( How to clean?

    By fuchs,
    • 1 reply
    • 1.4k views

  6. Filament stops running smooth halfway

    By ultifow,
    • 0 replies
    • 1.2k views

  7. Cura, Printing over USB, Preheating?

    By yzorg,
    • 2 replies
    • 2.9k views

  8. The Cause of a Bowden Pop, will v2 extruder help

    By lohiaprateek,
    • 2 replies
    • 1.4k views

  9. Extruded volume gradually reducing

    By sven1729minus1,
    • 20 replies
    • 3.2k views

  10. Large surface flat prints - edges curve up ?

    By jonjude,
    • 8 replies
    • 3.7k views

  11. SD Card not working in Ulticontroller

    By banana97,
    • 3 replies
    • 1.5k views

  12. Filament no more extrude

    By sam,
    • 15 replies
    • 2.1k views

  13. a slight leakage

    By hodge776,
    • 2 replies
    • 1.2k views

  14. "Temperature measurement failed"

    By infinityvisions,
    • 4 replies
    • 2.6k views

  15. Extruder overflow

    By nab,
    • 2 replies
    • 5.4k views

  16. Extruded volume gradually reducing

    By sven1729minus1,
    • 0 replies
    • 1.1k views

  17. Super. ultimaker restarts when temp is reached

    By ian,
    • 2 replies
    • 1.5k views

  18. Ultimaker in the UK

    By ronp-uk,
    • 3 replies
    • 1.3k views

  19. UltiController progress status

    By zungara,
    • 3 replies
    • 1.4k views

  20. Printing ABS On Ultimaker

    By magicxman,
    • 14 replies
    • 3.6k views

  21. a question about Cura checks after assembly

    By nab,
    • 4 replies
    • 1.4k views

  22. How to adjust Steps per E in Printrun?

    By banana97,
    • 10 replies
    • 5.5k views

  23. Any tips on getting the bowden cut perfectly straight?

    By IRobertI,
    • 14 replies
    • 9.3k views

  24. Extruder Drive Cannot Push Filament Through Hot End 1 2

    By calinb,
    • 32 replies
    • 20.1k views

  25. MAXTEMP triggered error

    By sven1729,
    • 3 replies
    • 2k views

  • Our picks

    • Introducing the UltiMaker Factor 4

      Introducing the UltiMaker Factor 4

      ArunC posted a topic in UltiMaker 3D printers,

      We are happy to announce the next evolution in the UltiMaker 3D printer lineup: the UltiMaker Factor 4 industrial-grade 3D printer, designed to take manufacturing to new levels of efficiency and reliability. Factor 4 is an end-to-end 3D printing solution for light industrial applications
      • 3 replies
      MariMakes

      Picked By

      MariMakes,
    • UltiMaker Cura 5.7 stable released

      UltiMaker Cura 5.7 stable released

      ArunC posted a topic in UltiMaker Cura,

      Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
       
      • 26 replies
      MariMakes

      Picked By

      MariMakes,
    View All
×
×
  • Create New...