Improve your 3D prints

5,368 topics in this forum

1. GCode Slice Off Center

   By LrGraham57, February 17   

   • Ender 3 Pro
   • cura 5.6
   • (and 2 more)

     Tagged with:

     • Ender 3 Pro
     • cura 5.6
     • offset
     • GCODE
   • 2 replies
   • 131 views
   • 
   • LrGraham57
   • February 17

2. Slice at an angle

   By msundman, February 1, 2021   

   • Help
   • 23 replies
   • 5.4k views
   • 
   • sinus50hz
   • February 15

3. Warping in same location for larger prints

   By rkondakjian, February 8
   • 11 replies
   • 237 views
   • 
   • gr5
   • February 15

4. Gaps in circles

   By 3dnerd, November 12, 2021   

   • UM2+
   • 12 replies
   • 2k views
   • 
   • gr5
   • February 15

5. PETG printing problems

   By Corrado1, February 12   

   • PETG
   • Stringing
   • 2 replies
   • 165 views
   • 
   • Corrado1
   • February 14

6. 1.0mm nozzle odd top/bottom shrinking

   By jaysenodell, February 11
   • 19 replies
   • 304 views
   • 
   • Slashee_the_Cow
   • February 14

7. Wall thickness change after Z seam

   By stevewhite, February 12
   • 4 replies
   • 146 views
   • 
   • stevewhite
   • February 13

8. Advice requested - Will this print?

   By glen4cindy, February 10
   • 8 replies
   • 186 views
   • 
   • jaysenodell
   • February 13

9. Even/Odd Slicing Mode ? For lightweight PLA : drones/rc planes

   By mscir, February 13
   • 2 replies
   • 168 views
   • 
   • mscir
   • February 13

10. Best fast but good quality settings

    By Simonsrk, February 12   

    • Cura
    • settings
    • (and 2 more)

      Tagged with:

      • Cura
      • settings
      • fast
      • quality
    • 1 reply
    • 246 views
    • 
    • Slashee_the_Cow
    • February 13

11. Little Blister Issue?

    By MikeTX, February 12
    • 1 reply
    • 95 views
    • 
    • MikeTX
    • February 12

12. Managing GCode vs 3mf

    By jaysenodell, February 11
    • 2 replies
    • 152 views
    • 
    • jaysenodell
    • February 12

13. Good layer, Bad layer

    By aaron81006, January 26
    • 7 replies
    • 233 views
    • 
    • Slashee_the_Cow
    • February 12

14. Weird porous wall defects on 3D prints

    By Arthpatel9497, February 5   

    • Walls
    • Porous
    • (and 5 more)

      Tagged with:

      • Walls
      • Porous
      • Porous walls
      • Porosity defect
      • Thin wall defects
      • Wavy wall defects
      • Wavy thin walls
    • 3 replies
    • 202 views
    • 
    • Slashee_the_Cow
    • February 11

15. empty spaces at the bottom

    By Corrado1, February 7   

    • bottom layer
    • 4 replies
    • 186 views
    • 
    • Slashee_the_Cow
    • February 9

16. Bad print results

    By Biem1000, February 4
    • 4 replies
    • 247 views
    • 
    • gr5
    • February 7

17. Easier support removal

    By jaysenodell, February 6
    • 7 replies
    • 702 views
    • 
    • jaysenodell
    • February 7

18. FEATURE REQUIRED: DIFFERENT LINE WIDTH FOR BOTTOM SKIN

    By centunesima, February 6
    • 3 replies
    • 142 views
    • 
    • Slashee_the_Cow
    • February 6

19. Spider webs from hades… or excess pla stinginess

    By jaysenodell, February 2
    • 6 replies
    • 182 views
    • 
    • Slashee_the_Cow
    • February 6

20. Traffic Cone 1:8 Print - strange slicer behavior

    By kerezst, February 5
    • 1 reply
    • 114 views
    • 
    • Slashee_the_Cow
    • February 5

21. I have a question about my ender 3 printing

    By dave1956, January 15
    • 5 replies
    • 168 views
    • 
    • Carlbosson
    • February 5

22. Arrêt de l'extrusion à 98% d'impression quelque soit l'objet

    By Mamou, February 1
    • 1 reply
    • 164 views
    • 
    • Slashee_the_Cow
    • February 3

23. Problem with a print / stringing with small figures / bed adhesion? Picture below

    By Sallyx1, February 1
    • 1 reply
    • 98 views
    • 
    • GregValiant
    • February 1

24. Sporadic layer height changes during print

    By rkondakjian, January 31
    • 1 reply
    • 120 views
    • 
    • rkondakjian
    • January 31

25. Noob mind boggled with slicing STL vs G-code file not printing same quality.

    By Mr_Stark1981, January 20   

    • G-code
    • layers
    • (and 2 more)

      Tagged with:

      • G-code
      • layers
      • Stringing
      • Supports
    • 17 replies
    • 337 views
    • 
    • Slashee_the_Cow
    • January 29