Jump to content

UltiMaker 3D printers

Our line of reliable 3D printers 

8,813 topics in this forum

  1. PVA Removal Station

    By MPestana,
    • 6 replies
    • 854 views

  2. Setting up Ultimaker S7 - Cura doesn't support S7?

    By DmOcRsI,
    • 3 replies
    • 797 views

  3. Backflow ABS

    By DesignFactory,
    • 3 replies
    • 376 views

  4. Setting up a new S5. Any special bench/desk required?

    By sandiegostateresearchfoundation,
    • 2 replies
    • 399 views

  5. Printcore in slot 2 is taking too long to warm up

    By abdulkhalik96,
    • 0 replies
    • 321 views

  6. Modified Gcode does not output constant temperature

    By awe,
    • 0 replies
    • 289 views

  7. Video that shows how to align the axles? - UM S5

    By libertyhouseplans,
    • 1 reply
    • 472 views

  8. Ultimate S5 ER32 Fault

    By Madigan,
    • 1 reply
    • 300 views

  9. Conflict errors, print cores not reaching temperature

    By Ellworx,   
    • 4 replies
    • 696 views

  10. UMS5 Support Structure - Support is too thick and it is impossible to remove

    By lukewjarboe,   
    • 4 replies
    • 1.4k views

  11. Ultimaker Original+ filament always deforms inside PEEK/teflon coupler/brass pipe

    By ansonl,
    • 1 reply
    • 557 views

  12. Wish list of minor tweaks/ upgrades to the UM S5, and the Material Station

    By orangepeel,   
    • 0 replies
    • 309 views

  13. Printer doesn´t store 3d party profiles

    By MPestana,
    • 0 replies
    • 310 views

  14. Tune screen not reading temps

    By mrender,   
    • 16 replies
    • 1.1k views

  15. Unknown build plate type

    By Jose77,   
    • 6 replies
    • 2.6k views

  16. Ultimaker S5 - Unknown Build Plate Type

    By lukewjarboe,   
    • 5 replies
    • 2.5k views

  17. Big problem with S3

    By RafaOrtiz,
    • 0 replies
    • 291 views

  18. PVA Stuck

    By oakcreeklibrary,
    • 0 replies
    • 453 views

  19. UM s5 voltage of capacitive sensor? sensor problems

    By bacon,
    • 2 replies
    • 300 views

  20. how to load filament in S5 with material station

    By bacon,
    • 5 replies
    • 1.4k views

  21. Printing without print head fan?

    By 2go,
    • 1 reply
    • 272 views

  22. how to skip active levelling phase of UM S5

    By bacon,
    • 1 reply
    • 431 views

  23. Slight inconsistent outer wall alignment using Cura 5.2.1 and an Ultimaker S5. Pics of issue as well as settings in comments

    By Jhawk6553,
    • 0 replies
    • 266 views

  24. UM S5 print head heatsink fan question

    By bacon,
    • 4 replies
    • 410 views

  25. Calibration Sheet A4 vs US 8.5x11 - can someone share the measurements of the boxes printed out?

    By kayakbabe,
    • 1 reply
    • 341 views

  • Our picks

    • Introducing the UltiMaker Factor 4

      Introducing the UltiMaker Factor 4

      ArunC posted a topic in UltiMaker 3D printers,

      We are happy to announce the next evolution in the UltiMaker 3D printer lineup: the UltiMaker Factor 4 industrial-grade 3D printer, designed to take manufacturing to new levels of efficiency and reliability. Factor 4 is an end-to-end 3D printing solution for light industrial applications
      • 2 replies
      MariMakes

      Picked By

      MariMakes,
    • UltiMaker Cura 5.7 stable released

      UltiMaker Cura 5.7 stable released

      ArunC posted a topic in UltiMaker Cura,

      Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
       
      • 26 replies
      MariMakes

      Picked By

      MariMakes,
    View All
×
×
  • Create New...