Jump to content

Improve your 3D prints

Help, tips & tricks

5,367 topics in this forum

  1. Help Needed: Trouble with 3D Printing a Custom Phone Case!

    By Lily492,
    • 2 replies
    • 192 views

  2. Layer expansion printing PC

    By alnavasa,
    • 0 replies
    • 131 views

  3. Cura not slicing part of my model

    By Mkono1,
    • 7 replies
    • 262 views

  4. Help?

    By Troycrawford73,
    • 5 replies
    • 234 views

  5. Help with File

    By Claro,
    • 1 reply
    • 148 views

  6. What is gap in vertical layers referred to?

    By rkondakjian,
    • 5 replies
    • 167 views

  7. Filament clumping and detaching from bed

    By Electricfuse,
    • 5 replies
    • 684 views

  8. gaps in top layer

    By Electricfuse,
    • 4 replies
    • 179 views

  9. Ultimaker 1+ print quality is getting worse, what can I do?

    By polle,
    • 1 reply
    • 206 views

  10. Thin spaced out lines

    By jkagi88,
    • 1 reply
    • 123 views

  11. Cura Custom Support Extends Down to Build Plate

    By ecsuka,   
    • 6 replies
    • 2.5k views

  12. Glistening in same layer print

    By rkondakjian,
    • 1 reply
    • 127 views

  13. I feel like I am about to lose my mind over the Ender 3 v2.

    By Thomas621,
    • 10 replies
    • 533 views

  14. Curves are printing in segments and not a single curve

    By Rowland_2009,
    • 2 replies
    • 269 views

  15. Trouble Calibrating the X Y Axis on the S5

    By murrjoh1,
    • 3 replies
    • 209 views

  16. How exactly do you print a TempTower?

    By rkondakjian,
    • 1 reply
    • 406 views

  17. Gaps between adjacent linear infill

    By ttaiwo,
    • 6 replies
    • 293 views

  18. 3D printer causes drops in the middle of infill pattern bottom layer

    By robba94,
    • 1 reply
    • 158 views

  19. Hello gurus, what do you suppose could be causing this?

    By HienoKaveri,
    • 13 replies
    • 392 views

  20. Thin walls or possible holes.

    By mcweb,
    • 2 replies
    • 277 views

  21. (SOLVED) Layer shifting (again)

    By Kevig,   
    • 15 replies
    • 23.4k views

  22. CPE+ print very high shrinkage and stuck to glass bed

    By alfonsvh,
    • 4 replies
    • 210 views

  23. Outer wall in one continuous pass

    By ModuloFS,
    • 3 replies
    • 479 views

  24. Printing Starts Printing off Bed

    By sdiutkin,
    • 2 replies
    • 211 views

  25. Print Starts off the bed

    By gustrowsky,   
    • 10 replies
    • 5.3k views

  • Our picks

    • UltiMaker Cura 5.7 stable released

      UltiMaker Cura 5.7 stable released

      ArunC posted a topic in UltiMaker Cura,

      Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
       
      • 18 replies
      MariMakes

      Picked By

      MariMakes,

    • Release Notes: S-Line Firmware 8.3.0 (Latest)

      Dustin posted a topic in Firmware,

      S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
      (Sorry, was out of office when this released)

      This update is for...
      All UltiMaker S series  
      New features
       
      Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
      • 0 replies
      MariMakes

      Picked By

      MariMakes,
    View All
×
×
  • Create New...