Deutsch

3,103 topics in this forum

1. Ultimaker 2 verschiebt Schichten in Y-Achsen Richtung

   By Printed-Vision, July 9, 2015
   • 6 replies
   • 2.2k views
   • 
   • MAChimo
   • July 15, 2015

2. Ultimaker 2 druckt zu dünne Wände

   By Sebastian1986, July 11, 2015
   • 4 replies
   • 2.4k views
   • 
   • Sebastian1986
   • July 11, 2015

3. UM2 - Druckkopf Gehäuse angebrochen

   By oceanblue72, January 25, 2015
   • 13 replies
   • 3.3k views
   • 
   • backinblack81
   • July 11, 2015

4. Ultimaker Original Plus Schrittmotoren Strom einstellen

   By Megi10, July 10, 2015
   • 0 replies
   • 1.4k views
   • 
   • Megi10
   • July 10, 2015

5. Geruchsbelästigung UM2 ABS

   By NBroenner, July 10, 2015
   • 0 replies
   • 1.4k views
   • 
   • NBroenner
   • July 10, 2015

6. Ultimaker 2 und PLA zu verkaufen / 2 Monate alt, technisch alles top

   By multan, October 21, 2014
   • 12 replies
   • 3.9k views
   • 
   • PropFiction
   • July 9, 2015

7. Verkaufe Ultimaker 2 - München

   By qbert3, May 20, 2015
   • 7 replies
   • 2.6k views
   • 
   • PropFiction
   • July 9, 2015

8. iGo3D sucht Techniker für den technischen Support

   By TobiasRedlin, July 8, 2015
   • 0 replies
   • 1.3k views
   • 
   • TobiasRedlin
   • July 8, 2015

9. Camaro 3D Modell für Druck vorbereiten

   By chris123, July 7, 2015
   • 0 replies
   • 1.6k views
   • 
   • chris123
   • July 7, 2015

10. Kleine Teile 1 2

    By hofmanns-modellbau, June 2, 2015
    • 42 replies
    • 5.7k views
    • 
    • NBroenner
    • July 7, 2015

11. Cura 15.6.... läuft bei mir sehr schlecht auf Mac OS X

    By ll1977, July 3, 2015
    • 3 replies
    • 2k views
    • 
    • Nicolinux
    • July 5, 2015

12. An alle Benutzer eines IRobertI Feeders

    By backinblack81, June 7, 2015
    • 3 replies
    • 1.5k views
    • 
    • Nicolinux
    • July 1, 2015

13. Probleme mit schmalen Kanten

    By tekknik, June 15, 2015
    • 1 reply
    • 1.6k views
    • 
    • Nicolinux
    • July 1, 2015

14. Sketch-Prints beschleunigen

    By clemens, January 8, 2015
    • 4 replies
    • 1.5k views
    • 
    • clems
    • July 1, 2015

15. UM2 auf zwei Farben/Düsen umbauen aber welches System?

    By martin-hillenbrand, June 22, 2015
    • 12 replies
    • 3.4k views
    • 
    • martin-hillenbrand
    • June 27, 2015

16. Ultimaker erste Schicht

    By cgu, June 22, 2015
    • 5 replies
    • 7.5k views
    • 
    • dirkdirk
    • June 24, 2015

17. Wo bestellt man UM2 Ersatzteile? 1 2

    By 3dnerd, February 9, 2015
    • 26 replies
    • 17k views
    • 
    • martin-hillenbrand
    • June 22, 2015

18. Wartung wegen schlechten Druckergebnissen nach mehr als 2000 Druckstunden

    By martin-garst, June 20, 2015
    • 4 replies
    • 2.4k views
    • 
    • martin-garst
    • June 21, 2015

19. Ptfe Coupler Ring

    By dirkdirk, June 20, 2015
    • 6 replies
    • 2.1k views
    • 
    • dirkdirk
    • June 20, 2015

20. rauch aus dem Extruder/Nozzle

    By stoque, June 19, 2015
    • 1 reply
    • 2.6k views
    • 
    • jonnybischof
    • June 19, 2015

21. Porblem beim drucken

    By stoque, June 10, 2015
    • 3 replies
    • 1.7k views
    • 
    • stoque
    • June 19, 2015

22. Problem mit Material PLA, 3mm

    By alaschgari, June 5, 2015
    • 3 replies
    • 2k views
    • 
    • chris123
    • June 17, 2015

23. Ultimaker 2 Optimierungen

    By NBroenner, May 21, 2015
    • 7 replies
    • 2.4k views
    • 
    • NBroenner
    • June 14, 2015

24. Ultimaker Original+ Platine anschließen

    By Olifantenber, June 14, 2015
    • 0 replies
    • 1.7k views
    • 
    • Olifantenber
    • June 14, 2015

25. Vergleich der Masse des Objekt mit den Angaben aus dem Slicer / berechnetes Volumen

    By backinblack81, June 10, 2015
    • 2 replies
    • 1.6k views
    • 
    • backinblack81
    • June 13, 2015