Jump to content

Improve your 3D prints

Help, tips & tricks

5,369 topics in this forum

  1. Prime Tower. Material order. Choose Internal and external.HELP

    By fundamental4,   
    • 0 replies
    • 347 views

  2. Help with Cura settings

    By Reverse_Engineer,
    • 1 reply
    • 825 views

  3. Power Outage

    By APuser,
    • 1 reply
    • 1.3k views

  4. PLA filament breaks during cold pull

    By lschachtner,
    • 2 replies
    • 2.5k views

  5. Dotted printing

    By Hazik,   
    • 4 replies
    • 5.2k views

  6. Support Blocker using Cura 3.4.1

    By RocketNut,
    • 0 replies
    • 390 views

  7. Anet A8 Auto Leveling, after 3 point calibration, crash into bed

    By DKAudio,
    • 1 reply
    • 1.9k views

  8. printer restart on its own

    By Eug,
    • 2 replies
    • 502 views

  9. Round Prints

    By MLode,   
    • 4 replies
    • 1.1k views

  10. Gab between layer start and stop.

    By NBull,   
    • 4 replies
    • 751 views

  11. Is it possible to repair the AA core?

    By federgarrido,
    • 2 replies
    • 458 views

  12. Switched from v2.1.1 to 2.1.4 motherboard due to burnt out fan, bought one on ali, and now the printer bed and nozzle move back and forth.

    By ccat676,   
    • 0 replies
    • 437 views

  13. PLA-PVA. PVA lines adhesion problem on PLA brim.

    By fundamental4,   
    • 1 reply
    • 655 views

  14. pre- and post- print instructions missing - solved

    By LesHall,   
    • 1 reply
    • 605 views

  15. How to save end of spools?

    By Brulti,   
    • 11 replies
    • 799 views

  16. Detected height printcores issue - Fixed!!

    By DanielW,   
    • 0 replies
    • 487 views

  17. PLA doesnt fill all the way to the walls

    By Jason138,   
    • 2 replies
    • 417 views

  18. How do I print with infil open on the top and bottom

    By eviL1776,
    • 1 reply
    • 765 views

  19. First prints

    By APuser,
    • 2 replies
    • 609 views

  20. [SOLVED] Can't get a descent print out of Cura

    By Mr_Pioupiou,
    • 2 replies
    • 2.8k views

  21. Da Clumsy Noob discovers a way to hot pull PVA midprint 1 2

    By kmanstudios,   
    • 29 replies
    • 3.4k views

  22. Strange Ringing Issue

    By tjippi,
    • 0 replies
    • 441 views

  23. Printing with .25 nozzle

    By bob-hepple,
    • 3 replies
    • 1.9k views

  24. Ultimaker S5 Something is wrong with your file

    By ily97,
    • 2 replies
    • 1.4k views

  25. UM3 doesn't take the IP adress from DHCP

    By Max_Jourdren,   
    • 4 replies
    • 1.5k views

  • Our picks

    • UltiMaker Cura 5.7 stable released

      UltiMaker Cura 5.7 stable released

      ArunC posted a topic in UltiMaker Cura,

      Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
       
        • Like
      • 18 replies
      MariMakes

      Picked By

      MariMakes,

    • Release Notes: S-Line Firmware 8.3.0 (Latest)

      Dustin posted a topic in Firmware,

      S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
      (Sorry, was out of office when this released)

      This update is for...
      All UltiMaker S series  
      New features
       
      Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
        • Like
      • 0 replies
      MariMakes

      Picked By

      MariMakes,
    View All
×
×
  • Create New...