Jump to content

Improve your 3D prints

Help, tips & tricks

5,369 topics in this forum

  1. First benchy problem

    By Ertzerzul,   
    • 3 replies
    • 1.6k views

  2. gcode

    By Creeperdog05,   
    • 2 replies
    • 895 views

  3. PVA going thinner during printing (big size model)

    By sol_1234,   
    • 2 replies
    • 867 views

  4. filaments become thin among printing,,,

    By sol_1234,
    • 2 replies
    • 545 views

  5. Control of infill layer alternation

    By Cathalo,
    • 2 replies
    • 1.7k views

  6. Ultimaker 3 Extended 2 colors

    By Aage Rasmussen,   
    • 1 reply
    • 563 views

  7. Min torq for direct drive?

    By SG91,
    • 0 replies
    • 420 views

  8. 20 sec. of pause at each layer change... is my printer refusing to work?

    By Harry Plotter,
    • 2 replies
    • 704 views

  9. Creality Ender 3 Printer stops mid print

    By jfisher,   
    • 6 replies
    • 18.1k views

  10. HELP: BB 0.4 Print Core - Ultimaker 3+ Extended

    By thomasbennett,
    • 1 reply
    • 800 views

  11. Visible support structure

    By Roman-InventoTeam,
    • 5 replies
    • 864 views

  12. how do I print an arch? (layer separation, crack, cloggy nozzle, bad support contact surface & more), and bed tilt?

    By crikp,
    • 4 replies
    • 1.4k views

  13. Print-quality 1 2

    By liba,
    • 28 replies
    • 1.9k views

  14. A lot of overextrusion I think...

    By ErenUenal,   
    • 3 replies
    • 924 views

  15. Please help with strange one-sided under extrusion on ABS prints

    By FeherAron,
    • 8 replies
    • 1.7k views

  16. Always failed to print Ninjaflex with my UM3, HELP!!!!!

    By xiaomage,   
    • 4 replies
    • 726 views

  17. STL missing holes

    By AndyG,   
    • 2 replies
    • 1.4k views

  18. Colorfabb XT -- Co-polyester -- Best Settings

    By rumbaughsm,
    • 19 replies
    • 10.6k views

  19. Loading an STL file from a network drive

    By jens3,
    • 4 replies
    • 1.3k views

  20. Finish on the underside of a supported section

    By jens3,
    • 8 replies
    • 2.3k views

  21. Installed 3.6.0

    By jens3,
    • 0 replies
    • 400 views

  22. cura not loading full g code to sd card are hard drive only works 1 out of 20 sometimes

    By 4k3ith20,
    • 1 reply
    • 648 views

  23. UM 3 won't stop active levelling, doesn't actually print

    By Huxster2000,
    • 3 replies
    • 595 views

  24. 3D recognition

    By eric992,   
    • 4 replies
    • 712 views

  25. File not showing up

    By Calluway29,
    • 2 replies
    • 710 views

  • Our picks

    • UltiMaker Cura 5.7 stable released

      UltiMaker Cura 5.7 stable released

      ArunC posted a topic in UltiMaker Cura,

      Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
       
      • 18 replies
      MariMakes

      Picked By

      MariMakes,

    • Release Notes: S-Line Firmware 8.3.0 (Latest)

      Dustin posted a topic in Firmware,

      S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
      (Sorry, was out of office when this released)

      This update is for...
      All UltiMaker S series  
      New features
       
      Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
      • 0 replies
      MariMakes

      Picked By

      MariMakes,
    View All
×
×
  • Create New...